Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2012.10
RM1840EF _59 Vehicle Exterior _009652 DOOR / HATCH _0052799 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (w/ Power Window)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Power Window)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window)

a.
B277019
0.083,0.052 0.385,0.281 0.302,0.229 10 false *A 0.083,2.292 0.438,2.458 0.354,0.167 10 false *B
*A for Double Cab
*B for Single Cab


Using a moulding remover, detach the 2 clips.


b.

Disconnect the 4 claws and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 4.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window, for Passenger Side)

a.
B277020

Using a moulding remover, detach the 2 clips.


b.

Disconnect the 4 claws and remove the power window regulator switch assembly with front door armrest base panel.


Hide 5.REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B277021
1.021,1.354 0.802,1.583 0.802,1.583 0.552,1.583 false 0.354,1.479 0.604,1.656 0.25,0.177 10 false *1
*1 Protective Tape


Insert a clip remover between the plate and trim board.

HINT:

Tape the clip remover tip before use.



b.

Turn the handle counterclockwise to remove the snap ring, front door window regulator handle and plate.


Hide 6.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B277018
0.063,0.063 0.417,0.333 0.354,0.271 10 false *A 0.063,1.521 0.417,1.76 0.354,0.24 10 false *B
*A w/o Front No. 2 Speaker
*B w/ Front No. 2 Speaker


Detach the 2 clips and remove the front door lower frame bracket garnish.


Hide 7.REMOVE DOOR PULL HANDLE

a.
B277022

Remove the screw and door pull handle.


Hide 8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B277024
3.177,1.073 3.177,0.948 false 3.198,1.677 3.198,1.563 false 3.104,1.073 3.333,1.25 0.229,0.177 10 false *1 3.135,1.698 3.375,1.885 0.24,0.188 10 false *2
*1 Clip
*2 Screw


for Double Cab:

i.

Remove the clip and screw.


ii.

Detach the 8 clips and remove the front door trim board.



b.
B277023
3.115,0.927 3.115,1.104 false 3.146,1.552 3.146,1.729 false 3.021,1.125 3.188,1.271 0.167,0.146 10 false *1 3.063,1.75 3.229,1.896 0.167,0.146 10 false *2
*1 Clip
*2 Screw


for Single Cab, for Extra Cab:

i.

Remove the clip and screw.


ii.

Detach the 9 clips and remove the front door trim board.



Hide 9.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B278549

for Double Cab:

i.

Raise the 7 claws of the front door inner glass weatherstrip as shown in the illustration, and then remove the front door inner glass weatherstrip from the front door trim board.



b.
B278550

for Single Cab, for Extra Cab:

i.

Raise the 8 claws of the front door inner glass weatherstrip as shown in the illustration, and then remove the front door inner glass weatherstrip from the front door trim board.



Hide 11.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Hide 12.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B277027
1.031,0.5 1.302,0.729 0.271,0.229 10 false (1) 1.76,3 2.094,3.25 0.333,0.25 10 false (2)

Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.


b.
B277028

Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.


Hide 14.REMOVE FRONT DOOR NO. 1 TRIM BRACKET

a.
B277026

Remove the 2 screws and front door No. 1 trim bracket.


Hide 15.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B281060

Pull out the front door inside locking cable, front door lock remote control cable and wire harness from the front door service hole cover, and then remove the front door service hole cover.

HINT:

Remove any remaining butyl tape from the front door panel.



Hide 16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

w/ Power Window:

i.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door glass sub-assembly so that the front door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



v.

Remove the power window regulator master switch assembly with front door armrest base panel.



b.

w/o Power Window:

i.

Temporarily install the door window regulator handle.


ii.

Move the front door glass sub-assembly so that the front door glass bolts can be seen.


iii.

Remove the door window regulator handle.



c.
B277030

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass to fall.



d.
B277031
1.656,0 1.885,0.198 0.229,0.198 10 false (1) 2.333,0.323 2.563,0.521 0.229,0.198 10 false (2)

Remove the front door glass as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass.



Hide 17.REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH

Hide 18.REMOVE FRONT DOOR GLASS RUN LH

a.
B277034

Remove the front door glass run.


Hide 19.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

w/ Power Window:

i.
B342491
2.292,0.417 2.115,0.167 2.115,0.167 2,0.167 true 1.813,0.063 2.125,0.219 0.313,0.156 10 false *1
*1 Temporary Bolt


Disconnect the connector.


ii.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator may fall and become damaged.



iii.

Remove the 5 bolts and front door power window regulator.


iv.

Remove the temporary bolt from the front door power window regulator.



b.

w/o Power Window:

i.
B342494
2.313,0.521 2.052,0.24 2.052,0.24 1.885,0.24 true 1.708,0.146 2.021,0.302 0.313,0.156 10 false *1
*1 Temporary Bolt


Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and become damaged.



ii.

Remove the 4 bolts and front door window regulator.


iii.

Remove the temporary bolt from the front door window regulator.



Hide 20.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

Hide 21.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B277035

Remove the 2 nuts and front door rear lower frame.


Hide 22.REMOVE FRONT DOOR OUTSIDE HANDLE COVER

a.
B277036

Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover together with door key cylinder.


c.
B277037

Detach the 2 claws and remove the front door outside handle cover from the door key cylinder.


Hide 23.REMOVE FRONT DOOR LOCK ASSEMBLY LH

a.

b.
B277039

w/o Power Door Lock:

i.

Disconnect the front door inside locking cable and front door lock remote control cable from the clamps.


ii.

Using a T30 "TORX" socket wrench, remove the 3 screws and front door lock.



Hide 24.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B278552

Remove the front door lock remote control cable.


Hide 25.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B278553

Detach the 3 claws and open the cover.


b.
B278554

Remove the front door inside locking cable.


Hide 26.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B277040

Remove the front door outside handle by sliding and pulling it in the direction indicated by the arrow in the illustration.


Hide 27.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B277041

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Detach the claw and remove the front door outside handle frame.


Hide 28.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B277042
1.875,0.229 1.688,0.229 1.688,0.229 1.531,0.438 false 1.896,0.125 2.094,0.313 0.198,0.188 10 false *1
*1 Snap


Rotate the snap in the direction indicated by the arrow in the illustration to detach the snap from the front door lock open rod.


b.

Remove the front door lock open rod from the front door outside handle frame.


Hide 29.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B277043

Detach the 2 claws and remove the front door front outside handle pad.


Hide 30.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B277044

Detach the 2 claws and remove the front door rear outside handle pad.


Hide 31.REMOVE FRONT DOOR PANEL CUSHION

a.
B277046

Remove the 2 front door panel cushions.


Hide 32.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B277049

for Double Cab:

i.

Remove the clip.


ii.

Detach the 33 clips and remove the front door weatherstrip.



b.
B277048

for Single Cab, for Extra Cab:

i.

Remove the clip.


ii.

Detach the 34 clips and remove the front door weatherstrip.



Hide 33.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B277045

Remove the 3 bolts and front door check.