Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2011.10–2012.01
RM1840EF _59 Vehicle Exterior _009652 DOOR / HATCH _0052799 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding areas of the front door check.


b.

When reusing a bolt labeled B:

i.

Clean the threads of the bolt labeled B with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt labeled B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B342501
1.948,0.51 2.104,0.25 2.104,0.25 2.406,0.25 true 1.906,1.292 1.865,1.125 1.865,1.125 1.719,1.125 false 1.229,1.979 1.5,1.979 1.5,1.979 1.573,1.802 true 2.458,0.146 2.771,0.302 0.313,0.156 10 false *1 1.073,1.885 1.385,2.042 0.313,0.156 10 false *2 1.563,1.031 1.875,1.188 0.313,0.156 10 false *1
*1 Bolt A
*2 Bolt B


Install the front door check with the 2 bolts labeled A and the bolt labeled B.

Torque:
Bolt A : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 2.INSTALL FRONT DOOR WEATHERSTRIP LH

HINT:

When installing the front door weatherstrip, heat the front door panel using a heat light.


Standard:
Item Temperature
Front Door Panel 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the front door panel excessively.


a.

Clean the front door panel surface.

i.

Using a heat light, heat the front door panel surface.


ii.

Remove the double-sided tape from the front door panel surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front door weatherstrip.

i.

for Double Cab:

1.

Remove the peeling paper from the face of the front door weatherstrip.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.


2.

Attach the 33 clips to install the front door weatherstrip.

HINT:

Press the front door weatherstrip firmly to install it.


3.

Install the clip.



ii.

for Single Cab:

1.

Remove the peeling paper from the face of the front door weatherstrip.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.


2.

Attach the 34 clips to install the front door weatherstrip.

HINT:

Press the front door weatherstrip firmly to install it.


3.

Install the clip.




Hide 3.INSTALL FRONT DOOR PANEL CUSHION

a.

Install a new front door panel cushion.


Hide 4.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the front door rear outside handle pad.


Hide 5.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.

Attach the 2 claws to install the front door front outside handle pad.


Hide 6.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B278558
1.417,0.51 1.698,1.104 1.698,1.104 1.906,1.104 true 1.969,0.99 2.281,1.219 0.313,0.229 10 false *1
*1 Snap


Install the front door lock open rod to the front door outside handle frame.


b.

Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the front door lock open rod.


Hide 7.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding area of the front door outside handle frame.


b.

Attach the claw to install the front door outside handle frame.


c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 36 in.*lbf)


Hide 8.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B278559

Install the front door outside handle by moving it in the direction indicated by the arrow shown in the illustration.


Hide 9.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the front door inside locking cable.


b.

Attach the 3 claws to close the cover.


Hide 10.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable.


Hide 11.INSTALL FRONT DOOR LOCK ASSEMBLY LH


b.

w/o Power Door Lock:

i.

Using a T30 "TORX" socket wrench, install the front door lock with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Connect the front door inside locking cable and front door lock remote control cable to the clamps.



Hide 12.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.

Attach the 2 claws to install the front door outside handle cover to the door key cylinder.


b.

Using a T30 "TORX" socket wrench, install the front door outside handle cover together with the door key cylinder with the screw.

Torque:
4.0 N*m (41 kgf*cm, 36 in.*lbf)


c.

Install the hole plug.


Hide 13.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.

Install the front door rear lower frame with the 2 nuts.


Hide 14.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

Hide 15.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B293962

w/ Power Window:

i.

Apply MP grease to the sliding and rotating areas of the front door window regulator.


ii.

Temporarily install the temporary bolt to the front door window regulator.


iii.
B342491
2.292,0.417 2.115,0.167 2.115,0.167 2,0.167 true 1.813,0.063 2.125,0.219 0.313,0.156 10 false *1
*1 Temporary Bolt


Install the front door window regulator with the 5 bolts, and then tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the front door window regulator as it may become damaged.



iv.

Connect the connector.



b.
B293963

w/o Power Window:

i.

Apply MP grease to the sliding and rotating areas of the front door window regulator.

NOTICE:

Do not apply grease to the spring of the window regulator.



ii.

Temporarily install the temporary bolt to the front door window regulator.


iii.
B342494
2.313,0.521 2.052,0.24 2.052,0.24 1.885,0.24 true 1.708,0.146 2.021,0.302 0.313,0.156 10 false *1
*1 Temporary Bolt


Install the front door window regulator with the 4 bolts, and then tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the front door window regulator as it may become damaged.




Hide 16.INSTALL FRONT DOOR GLASS RUN LH

a.

Install the front door glass run.


Hide 17.INSTALL FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH

Hide 18.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

w/ Power Window:

i.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Operate the front door window regulator so that the front door glass can be installed.


iv.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



v.

Remove the power window regulator master switch assembly with front door armrest base panel.



b.

w/o Power Window:

i.

Temporarily install the front door window regulator handle.


ii.

Operate the front door window regulator so that the front door glass can be installed.


iii.

Remove the front door window regulator handle.



c.
B277051
2.327,0.279 2.52,0.46 0.194,0.181 10 (1) 1.438,0.53 1.631,0.711 0.194,0.181 10 (2)

Insert the front door glass into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.


d.

Install the front door glass with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 19.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the front door panel.


b.
B281064
0.583,0.146 0.719,0.146 0.719,0.146 0.917,0.302 true 2.76,0.177 2.49,0.177 2.49,0.177 2.406,0.292 true 0.375,0.042 0.563,0.208 0.188,0.167 10 false *a 2.76,0.063 2.948,0.229 0.188,0.167 10 false *a
*a Reference Point


Pass the front door inside locking cable, front door lock remote control cable and wire harness through a new front door service hole cover, and then install the front door service hole cover using the reference points on the front door panel.


Hide 20.INSTALL FRONT DOOR NO. 1 TRIM BRACKET

a.

Install the front door No. 1 trim bracket with the 2 screws.


Hide 21.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Connect the front door inside locking cable and front door lock remote control cable to the front door inside handle.


b.
B278565

Attach the 2 guides as indicated by the arrow in the illustration, and then attach the claw to install the front door inside handle.


Hide 22.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 24.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Hide 25.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B278572

for Double Cab:

i.

Install the front door inner glass weatherstrip to the front door trim board and fold down the 7 claws in the directions indicated by the arrows in the illustration.



b.
B278573

for Single Cab:

i.

Install the front door inner glass weatherstrip to the front door trim board and fold down the 8 claws in the directions indicated by the arrows in the illustration.



Hide 26.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

for Double Cab:

i.

Attach the 8 clips to install the front door trim board.


ii.

Install the screw and clip.



b.

for Single Cab:

i.

Attach the 9 clips to install the front door trim board.


ii.

Install the screw and clip.



Hide 27.INSTALL DOOR PULL HANDLE

a.

Install the door pull handle with the screw.


Hide 28.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the 2 clips to install the front door lower frame bracket garnish.


Hide 29.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window)

a.

Connect the connector.


b.

Attach the 4 claws and 2 clips to install the power window regulator switch assembly with front door armrest base panel.


Hide 30.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window, for Passenger Side)

a.

Connect the connector.


b.

Attach the 4 claws and 2 clips to install the power window regulator master switch assembly with front door armrest base panel.


Hide 31.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.

Temporarily install the front door window regulator handle, fully close the window, and then remove the front door window regulator handle.


b.
B278578
1.313,1.552 1.26,1.552 1.26,1.552 1.198,1.146 false 1.75,1.552 1.667,1.552 1.667,1.552 1.469,1.146 false 2.49,0.302 2.688,0.5 0.198,0.198 10 false A 3.063,0.667 3.333,0.854 0.271,0.188 10 false *a 1.333,1.448 1.552,1.635 0.219,0.188 10 false *1 1.771,1.448 1.99,1.656 0.219,0.208 10 false *2
*1 Snap Ring
*2 Plate
*a Front Side


Install the plate and snap ring to the front door window regulator handle.


c.

Install the front door window regulator handle to the front door window regulator as shown in the illustration.

Standard:
Area Specified Condition
A 18 to 42°



Hide 32.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 33.INITIALIZE POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function)