Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM1840EF _59 Vehicle Exterior _009654 WIPER / WASHER _0052808 WIPER AND WASHER SYSTEM D

WIPER / WASHER  WIPER AND WASHER SYSTEM  SYSTEM DESCRIPTION  


WASHER LINKED OPERATION


a.

This system operates the front wipers at low speed immediately after spraying a jet of washer fluid when the front washer switch is turned on for 0.3 seconds or more. The system operates the front wipers at low speed for approximately 2.2 seconds and then stops operation when the washer switch is turned on for 1.5 seconds or more.



INTERMITTENT OPERATION


C240510
0.125,7.052 2.313,7.302 2.188,0.25 10 false *1: w/ Intermittent Time Adjust Dial 1.896,4.385 2.24,4.625 0.344,0.24 10 false WIP 2.354,6.323 3.479,6.75 1.125,0.427 10 false Windshield Wiper Motor Assembly 4.542,4.458 5.771,4.99 1.229,0.531 10 false Windshield Washer Motor and Pump Assembly 2.208,3.781 2.406,3.969 0.198,0.188 10 false +B 2.521,3.781 2.719,3.969 0.198,0.188 10 false +2 2.823,3.781 3.021,3.969 0.198,0.188 10 false +1 3.073,3.781 3.271,3.969 0.198,0.188 10 false +S 5.521,3.813 5.771,4 0.25,0.188 10 false WF 5.833,3.813 6.083,4 0.25,0.188 10 false EW 3.469,3.781 3.667,3.969 0.198,0.188 10 false C1 5.396,3.167 5.594,3.354 0.198,0.188 10 false C2 3.51,3.083 3.708,3.271 0.198,0.188 10 false *2 3.698,2.688 3.896,2.875 0.198,0.188 10 false *1 4.583,2.958 4.813,3.146 0.229,0.188 10 false Tr1 5.156,2.51 5.427,2.729 0.271,0.219 10 false Tr2 5.375,1.427 5.677,1.583 0.302,0.156 10 false OFF 5.74,1.281 5.896,1.438 0.156,0.156 10 false W 6,1.281 6.271,1.458 0.271,0.177 10 false EW 5.406,1.573 5.635,1.729 0.229,0.156 10 false ON 0.073,4.271 1.313,4.49 1.24,0.219 10 false from Ignition Switch 0.042,0.51 1.583,0.969 1.542,0.458 10 false Windshield Wiper Switch Assembly 2.479,0.406 4.052,0.781 1.573,0.375 10 false Windshield Wiper Switch 4.823,0.875 6.552,1.271 1.729,0.396 10 false Windshield Washer Switch 0.125,7.375 2.479,7.625 2.354,0.25 10 false *2: w/o Intermittent Time Adjust Dial 1.927,0.979 2.354,1.167 0.427,0.188 10 false MIST 2.354,0.823 2.594,1 0.24,0.177 10 false +B 2.646,0.823 2.865,1.021 0.219,0.198 10 false +2 2.979,0.823 3.188,1 0.208,0.177 10 false +1 3.26,0.823 3.5,1.031 0.24,0.208 10 false +S 3.49,0.823 3.844,1.031 0.354,0.208 10 false INT1 3.813,0.823 4.177,1.021 0.365,0.198 10 false INT2 4.188,0.823 4.417,1.042 0.229,0.219 10 false B1 1.958,1.125 2.302,1.323 0.344,0.198 10 false OFF 1.99,1.271 2.25,1.469 0.26,0.198 10 false INT 2,1.417 2.24,1.594 0.24,0.177 10 false LO 2.021,1.573 2.24,1.823 0.219,0.25 10 false HI

a.

w/ Intermittent Time Adjust Dial:

The system operates the front wipers once in approximately 1.6 to 10.7 seconds when the front wiper switch is turned to the INT position. The intermittent time can be adjusted from 1.6 to 10.7 seconds by using the intermittent time adjust dial.


b.

If the windshield wiper switch (front wiper switch) is turned to the INT position, current flows from the already charged capacitor C1 through terminals INT1 and INT2 of the front wiper switch to Tr1 (transistor). When Tr1 turns on, current flows from terminal +S of the front wiper switch to terminal +1 of the front wiper switch, to terminal +1 of the windshield wiper motor, to the windshield wiper motor and finally to ground, causing the windshield wiper motor to operate. At the same time, current flows from capacitor C1 to terminal INT1 of the front wiper switch and then INT2. When the current flow from capacitor C1 ends, Tr1 turns off to stop the relay contact point and halt the windshield wiper motor.

When the relay contact point turns off, capacitor C1 begins to charge again and Tr1 remains off until charging has been completed. This period corresponds to the intermittent time. When capacitor C1 is fully charged, Tr1 turns on and then the relay contact point turns on, causing the windshield wiper motor to operate again. This cycle is the intermittent operation.

The intermittent time can be adjusted by using the intermittent time adjust dial (variable resistor) to change the charge time of capacitor C1.


c.

w/o Intermittent Time Adjust Dial:

The system operates the front wipers once in approximately 3.3 +/-1 seconds when the front wiper switch is turned to the INT position.


d.

If the windshield wiper switch (front wiper switch) is turned to the INT position, current flows from the already charged capacitor C1 through terminals INT1 and INT2 of the front wiper switch to Tr1 (transistor). When Tr1 turns on, current flows from terminal +S of the front wiper switch to terminal +1 of the front wiper switch, to terminal +1 of the windshield wiper motor, to the windshield wiper motor and finally to ground, causing the windshield wiper motor to operate. At the same time, current flows from capacitor C1 to terminal INT1 of the front wiper switch and then INT2. When the current flow from capacitor C1 ends, Tr1 turns off to stop the relay contact point and halt the windshield wiper motor.

When the relay contact point turns off, capacitor C1 begins to charge again and Tr1 remains off until charging has been completed. This period corresponds to the intermittent time. When capacitor C1 is fully charged, Tr1 turns on and then the relay contact point turns on, causing the windshield wiper motor to operate again. This cycle is the intermittent operation.