Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM1840EF _59 Vehicle Exterior _009654 WIPER / WASHER _0052811 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

a.
E171721
0.25,1.094 0.573,1.333 0.323,0.24 2.917,1.094 3.281,1.333 0.365,0.24 2.063,1.052 2.063,0.552 2.063,0.552 2.146,0.552 true 1.604,1.063 1.604,0.563 1.604,0.563 1.688,0.563 true 1.438,1.063 1.438,0.375 1.438,0.375 1.302,0.375 true 2.26,1.052 2.656,0.552 2.656,0.552 2.74,0.552 true 1.177,1.052 1.063,0.49 1.063,0.49 0.948,0.49 true 0.99,1.063 0.833,0.719 0.833,0.719 0.708,0.719 true 1.677,0.094 1.917,0.323 0.24,0.229 10 false *a 0.344,1.146 0.531,1.313 0.188,0.167 10 false B 0.49,0.625 0.74,0.802 0.25,0.177 10 false +2 0.75,0.396 1.01,0.594 0.26,0.198 10 false +1 1.083,0.292 1.344,0.479 0.26,0.188 10 false +B 1.729,0.479 2.01,0.698 0.281,0.219 10 false +S 2.198,0.479 2.542,0.677 0.344,0.198 10 false WF 2.771,0.479 3.104,0.708 0.333,0.229 10 false EW 3.052,1.135 3.281,1.313 0.229,0.177 10 false A
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Check the front wiper switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
B-3 (+1) - B-2 (+B) MIST Below 1 Ω
B-3 (+1) - B-1 (+S) OFF Below 1 Ω
B-3 (+1) - B-1 (+S) INT Below 1 Ω
B-3 (+1) - B-2 (+B) LO Below 1 Ω
B-4 (+2) - B-2 (+B) HI Below 1 Ω




b.

Check the windshield washer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A-3 (WF) - A-2 (EW) OFF 10 kΩ or higher
A-3 (WF) - A-2 (EW) ON Below 1 Ω


If the result is not as specified, replace the switch assembly.



c.

Check the intermittent operation.

i.

Connect a voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).


ii.

Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals A-2 (EW) and B-1 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect the battery's positive (+) lead to terminal B-1 (+S) for 5 seconds.


v.

Connect the battery's negative (-) lead to terminal B-1 (+S). operate the intermittent wiper relay and check the voltage between terminals B-3 (+1) and A-2 (EW).

OK:

Refer to the illustration below.


E056399
0.708,0.969 0.938,1.167 0.229,0.198 10 false *a 1.729,0.573 2.49,0.75 0.76,0.177 10 false 11 to 14 V 2.198,1.052 2.469,1.208 0.271,0.156 10 false 0 V 2.896,1.448 3.229,1.698 0.333,0.25 10 false *d 2.688,0.271 2.938,0.469 0.25,0.198 10 false *b 4.74,0.26 5.021,0.5 0.281,0.24 10 false *c 5.146,1.479 5.365,1.656 0.219,0.177 10 false *e
*a Voltage between terminals B-3 (+1) and A-2 (EW) *b Battery negative lead is connected to terminal B-4 (+S)
*c Battery negative lead is connected to terminal B-4 (+S) *d 1.6 +/-1 second (interval is short)
*e 10.7 +/-5 second (interval is long) - -


If the result is not as specified, replace the switch assembly.



d.

Check the washer operation.

i.

Turn the wiper switch off.


ii.

Connect the battery's positive (+) lead to terminal B-2 (+B) and the negative (-) lead to terminals B-1 (+S) and A-2 (EW).


iii.

Connect the voltmeter's positive (+) lead to terminal B-3 (+1) and the negative (-) lead to terminal A-2 (EW).


iv.

Turn the washer switch on and off, and check the voltage between terminals B-3 (+1) and A-2 (EW).

OK:

Refer to the illustration below.


E125344
2.938,1.323 2.896,1.438 false 3.594,1.313 3.74,1.427 false 0.688,0.917 0.917,1.083 0.229,0.167 10 *a 0.688,0.542 1.646,0.698 0.958,0.156 10 *1 2.313,1.135 2.677,1.292 0.365,0.156 10 0 V 2.375,0.688 2.74,0.844 0.365,0.156 10 Off 2.375,0.5 2.646,0.656 0.271,0.156 10 On 2.042,0.938 2.76,1.083 0.719,0.146 10 11 to 14 V 1.792,1.438 3.521,1.583 1.729,0.146 10 Approximately 0.3 seconds 3.573,1.448 5.302,1.594 1.729,0.146 10 Approximately 2.2 seconds
*1 Washer Switch - -
*a Voltage between terminals A-2 (EW) and B-3 (+1) - -


If the result is not as specified, replace the switch assembly.