Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH
RM1840EF _59 Vehicle Exterior _009655 LIGHTING (EXT) _0052822 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (w/ Automatic Light Control System)

a.
E227035
2.229,1.323 2.448,1.656 true 1.49,1.302 1.542,1.646 true 1.365,1.313 1.198,1.646 true 1.021,1.198 0.688,1.198 true 1.771,1.313 1.979,1.646 true 2.417,1.208 2.844,1.052 true 2.063,1.313 2.25,1.656 true 2.792,0.542 2.083,1.031 true 1.938,1.031 0.813,0.531 true 0.865,1.698 1.198,1.323 true 1.635,1.313 1.802,1.635 true 2.427,1.677 2.781,1.938 0.354,0.26 10 false EL 1.135,1.667 1.333,1.938 0.198,0.271 10 false T 0.76,1.667 1.042,1.906 0.281,0.24 10 false A 1.479,1.667 1.75,1.927 0.271,0.26 10 false HF 0.073,0 2.615,0.354 2.542,0.354 10 false *a 2.885,0.958 3.229,1.229 0.344,0.271 10 false HU 2.198,1.677 2.5,1.917 0.302,0.24 10 false TR 1.979,1.667 2.26,1.938 0.281,0.271 10 false TL 2.844,0.438 3.313,0.76 0.469,0.323 10 false LFG 0.469,0.427 0.979,0.667 0.51,0.24 10 false BFG 0.563,1.115 0.781,1.354 0.219,0.24 10 false H 1.75,1.667 2.031,1.896 0.281,0.229 10 false HL
*a Component without harness connected (Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (HU) - 12 (EL) OFF 10 kΩ or higher
18 (T) - 12 (EL) TAIL Below 1 Ω
18 (T) - 12 (EL) HEAD Below 1 Ω
20 (H) - 12 (EL) HEAD Below 1 Ω
19 (A) - 12 (EL) AUTO Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
17 (HF) -12 (EL) FLASH Below 1 Ω
11 (HU) - 12 (EL) FLASH Below 1 Ω
16 (HL) - 12 (EL) LO BEAM Below 1 Ω
11 (HU) - 12 (EL) HI BEAM Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 (TR) - 12 (EL) Right turn Below 1 Ω
13 (TR) - 12 (EL) Neutral 10 kΩ or higher
15 (TL) - 12 (EL) Neutral 10 kΩ or higher
15 (TL) - 12 (EL) Left turn Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



d.

Inspect the fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (LFG) - 4 (BFG) OFF 10 kΩ or higher
3 (LFG) - 4 (BFG) ON Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



Hide 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

a.
E218654
0.708,0.427 1.104,0.896 true 0.51,0.865 0.896,0.948 true 0.521,1.219 0.896,1.198 true 0.948,1.573 1.344,1.25 true 1.385,1.563 1.521,1.25 true 1.719,1.26 1.729,1.552 true 1.927,1.26 2.104,1.552 true 2.135,1.25 2.458,1.573 true 2.344,1.24 2.781,1.563 true 2.531,1.177 2.875,1.156 true 0.115,0.052 0.438,0.302 0.323,0.25 10 false *a 0.208,0.771 0.625,1.021 0.417,0.25 10 false LFG 0.385,0.313 0.802,0.563 0.417,0.25 10 false BFG 0.313,1.146 0.667,1.375 0.354,0.229 10 false B1 0.802,1.583 1.094,1.865 0.292,0.281 10 false ED 1.271,1.583 1.531,1.885 0.26,0.302 10 false T1 1.646,1.573 1.99,1.844 0.344,0.271 10 false HU 2.083,1.563 2.406,1.865 0.323,0.302 10 false HL 2.458,1.583 2.688,1.833 0.229,0.25 10 false E 2.906,1.073 3.198,1.333 0.292,0.26 10 false TL 2.833,1.552 3.135,1.813 0.302,0.26 10 false TR
*a Component without harness connected (Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (HU) - 11 (ED) Light control switch off 10 kΩ or higher
8 (HL) - 11 (ED)
13 (B1) - 10 (T1) Light control switch tail Below 1 Ω
9 (HU) - 11 (ED) Light control switch head Below 1 Ω
8 (HL) - 11 (ED)


If the result is not as specified, replace the headlight dimmer switch assembly.



b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (HU) - 11 (ED) Headlight dimmer switch hi beam Below 1 Ω


HINT:

Perform the flash and high beam inspection with the light control switch on head.


If the result is not as specified, replace the headlight dimmer switch assembly.



c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (TR) - 7 (E) Turn signal switch right turn Below 1 Ω
6 (TR) - 7 (E) Turn signal switch right lane change Below 1 Ω
6 (TR) - 7 (E) Turn signal switch neutral 10 kΩ or higher
5 (TL) - 7 (E)
5 (TL) - 7 (E) Turn signal switch left lane change Below 1 Ω
5 (TL) - 7 (E) Turn signal switch left turn Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



d.

Inspect the fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (BFG) - 4 (LFG) Fog light switch off 10 kΩ or higher
3 (BFG) - 4 (LFG) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.