Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP › from 2012.10
RM1840EF _59 Vehicle Exterior _009657 EXTERIOR PANELS / TRIM _0052838 SIDE STEP A

EXTERIOR PANELS / TRIM  SIDE STEP  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.
B277505
0.375,0.844 0.656,1.063 0.281,0.219 10 false A

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

NOTICE:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



c.

Lightly press the drill against the 2 rivets, drill off the flanges of the 2 rivets and remove the No. 1 side step stay.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 2.REMOVE NO. 2 SIDE STEP BRACKET LH (for Extra Cab, for Double Cab)

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.
B277506
0.427,0.823 0.667,1.052 0.24,0.229 10 false A

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

NOTICE:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



c.

Lightly press the drill against the 2 rivets, drill off the flanges of the 2 rivets and remove the No. 2 side step bracket.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 3.REMOVE NO. 3 SIDE STEP BRACKET LH

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.
B277508
0.354,0.917 0.583,1.094 0.229,0.177 10 false A

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

NOTICE:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



c.

Lightly press the drill against the 2 rivets, drill off the flanges of the 2 rivets and remove the No. 3 side step bracket.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 4.REMOVE FRONT SIDE STEP PLATE COVER LH

a.
B277509

Remove the 2 screws.


b.

Detach the claw and remove the front side step plate cover.


Hide 5.REMOVE REAR SIDE STEP PLATE COVER LH

a.
B277510

Remove the 2 screws.


b.

Detach the claw and remove the rear side step plate cover.