Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP › from 2012.10
RM1840EF _59 Vehicle Exterior _009657 EXTERIOR PANELS / TRIM _0052838 SIDE STEP A

EXTERIOR PANELS / TRIM  SIDE STEP  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SIDE STEP PLATE COVER LH

a.

Attach the claw to install the front side step plate cover.


b.

Install the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 2.INSTALL REAR SIDE STEP PLATE COVER LH

a.

Attach the claw to install the rear side step plate cover.


b.

Install the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 3.INSTALL NO. 1 SIDE STEP STAY SUB-ASSEMBLY LH

a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new rivet into the nose piece.


c.
B277511

Using the riveter, install the No. 1 side step stay with the 2 rivets as shown in the illustration.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664
1.24,1.115 1.094,1.646 1.094,1.646 1.25,2.208 false 1.083,1.646 0.813,1.646 false 1.781,0.906 2.021,1.635 2.021,1.635 1.76,2.51 true 2.031,1.635 2.313,1.635 false 2.271,0.542 2.479,0.771 0.208,0.229 10 false *a 2.271,2.448 2.51,2.646 0.24,0.198 10 false *b 0.594,1.542 0.813,1.719 0.219,0.177 10 false *1 2.344,1.531 2.521,1.729 0.177,0.198 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390
0.719,0.104 1.021,0.104 false 0.802,1.146 1,1.146 false 0.792,2.427 0.99,2.427 false 2.344,0.573 2.656,0.833 0.313,0.26 10 false *a 2.354,1.531 2.708,1.75 0.354,0.219 10 false *a 2.375,2.76 2.688,2.958 0.313,0.198 10 false *b 1.031,2.323 1.208,2.479 0.177,0.156 10 false *1 1.042,1.042 1.302,1.219 0.26,0.177 10 false *1 1.042,0 1.333,0.177 0.292,0.177 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the No. 1 side step stay.

·

Do not tilt the riveter when installing the rivet to the No. 1 side step stay.

·

Do not leave any space between the rivet head and No. 1 side step stay.

·
B172391
0.729,0.646 0.927,0.646 false 0.729,2.125 0.938,2.125 false 2.302,1 2.615,1.25 0.313,0.25 10 false *a 2.292,2.479 2.646,2.719 0.354,0.24 10 false *b 0.969,0.521 1.292,0.719 0.323,0.198 10 false *1 0.969,2.01 1.24,2.219 0.271,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the No. 1 side step stay and step plate. Firmly hold together the 2 items while installing the rivet.




Hide 4.INSTALL NO. 2 SIDE STEP BRACKET LH (for Extra Cab, for Double Cab)

a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new rivet into the nose piece.


c.
B277512

Using the riveter, install the No. 2 side step bracket with the 2 rivets as shown in the illustration.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664
1.24,1.115 1.094,1.646 1.094,1.646 1.25,2.208 false 1.083,1.646 0.813,1.646 false 1.781,0.906 2.021,1.635 2.021,1.635 1.76,2.51 true 2.031,1.635 2.313,1.635 false 2.271,0.542 2.479,0.771 0.208,0.229 10 false *a 2.271,2.448 2.51,2.646 0.24,0.198 10 false *b 0.594,1.542 0.813,1.719 0.219,0.177 10 false *1 2.344,1.531 2.521,1.729 0.177,0.198 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390
0.719,0.104 1.021,0.104 false 0.802,1.146 1,1.146 false 0.792,2.427 0.99,2.427 false 2.344,0.573 2.656,0.833 0.313,0.26 10 false *a 2.354,1.531 2.708,1.75 0.354,0.219 10 false *a 2.375,2.76 2.688,2.958 0.313,0.198 10 false *b 1.031,2.323 1.208,2.479 0.177,0.156 10 false *1 1.042,1.042 1.302,1.219 0.26,0.177 10 false *1 1.042,0 1.333,0.177 0.292,0.177 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the No. 2 side step bracket.

·

Do not tilt the riveter when installing the rivet to the No. 2 side step bracket.

·

Do not leave any space between the rivet head and No. 2 side step bracket.

·
B172391
0.729,0.646 0.927,0.646 false 0.729,2.125 0.938,2.125 false 2.302,1 2.615,1.25 0.313,0.25 10 false *a 2.292,2.479 2.646,2.719 0.354,0.24 10 false *b 0.969,0.521 1.292,0.719 0.323,0.198 10 false *1 0.969,2.01 1.24,2.219 0.271,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the No. 2 side step bracket and step plate. Firmly hold together the 2 items while installing the rivet.




Hide 5.INSTALL NO. 3 SIDE STEP BRACKET LH

a.

Install a nose piece to an air riveter or hand riveter.


b.

Insert the mandrel part of a new rivet into the nose piece.


c.
B277514

Using the riveter, install the No. 3 side step bracket with the 2 rivets as shown in the illustration.

HINT:

If the rivet cannot be cut, pull it once and cut it.


NOTICE:
·
B171664
1.24,1.115 1.094,1.646 1.094,1.646 1.25,2.208 false 1.083,1.646 0.813,1.646 false 1.781,0.906 2.021,1.635 2.021,1.635 1.76,2.51 true 2.031,1.635 2.313,1.635 false 2.271,0.542 2.479,0.771 0.208,0.229 10 false *a 2.271,2.448 2.51,2.646 0.24,0.198 10 false *b 0.594,1.542 0.813,1.719 0.219,0.177 10 false *1 2.344,1.531 2.521,1.729 0.177,0.198 10 false *2
*1 Riveter
*2 Mandrel
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

·
B172390
0.719,0.104 1.021,0.104 false 0.802,1.146 1,1.146 false 0.792,2.427 0.99,2.427 false 2.344,0.573 2.656,0.833 0.313,0.26 10 false *a 2.354,1.531 2.708,1.75 0.354,0.219 10 false *a 2.375,2.76 2.688,2.958 0.313,0.198 10 false *b 1.031,2.323 1.208,2.479 0.177,0.156 10 false *1 1.042,1.042 1.302,1.219 0.26,0.177 10 false *1 1.042,0 1.333,0.177 0.292,0.177 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the No. 3 side step bracket.

·

Do not tilt the riveter when installing the rivet to the No. 3 side step bracket.

·

Do not leave any space between the rivet head and No. 3 side step bracket.

·
B172391
0.729,0.646 0.927,0.646 false 0.729,2.125 0.938,2.125 false 2.302,1 2.615,1.25 0.313,0.25 10 false *a 2.292,2.479 2.646,2.719 0.354,0.24 10 false *b 0.969,0.521 1.292,0.719 0.323,0.198 10 false *1 0.969,2.01 1.24,2.219 0.271,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the No. 3 side step bracket and step plate. Firmly hold together the 2 items while installing the rivet.