Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  P0021  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)  P0022  Camshaft Position "A" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

Refer to DTC P0010 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0010).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) Valve timing is not adjusted in valve timing advance range
(1 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


- DTC stored
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) Valve timing is not adjusted in valve timing retard range
(2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


- DTC stored
P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) Valve timing is not adjusted in valve timing advance range
(1 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


- DTC stored
P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) Valve timing is not adjusted in valve timing retard range
(2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


- DTC stored

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.


Example:

A DTC is stored when conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After condition 1 is met, the camshaft timing oil control valve assembly is forcibly activated 63 times or more.



CONFIRMATION DRIVING PATTERN

A232050
6.719,2.625 6.333,3.49 6.333,3.49 6.25,3.49 false 4.156,2.656 3.833,3.521 3.833,3.521 3.771,3.521 false 1.365,2.354 1.604,2.604 0.24,0.25 10 false [A] 1.875,2.063 2.125,2.302 0.25,0.24 10 false [B] 3.021,1 3.292,1.292 0.271,0.292 10 false [C] 4.052,2.313 4.323,2.594 0.271,0.281 10 false [D] 4.25,3.135 4.51,3.385 0.26,0.25 10 false [E] 5.448,2.219 5.729,2.563 0.281,0.344 10 false [F]* 6.615,2.302 6.927,2.625 0.313,0.323 10 false [G] 6.823,3.156 7.125,3.479 0.302,0.323 10 false [H] 0.135,2.292 1.042,2.677 0.906,0.385 10 false Ignition Switch ON 0.708,2.104 1.094,2.292 0.385,0.188 10 false Idling 0.031,1.094 1.156,1.563 1.125,0.469 10 false Approximately 60 km/h (37 mph) 0.167,0.375 1.115,0.688 0.948,0.313 10 false Vehicle Speed 1.615,2.76 2.427,3.052 0.813,0.292 10 false Warming up 2.563,2.771 3.792,3.01 1.229,0.24 10 false 10 minutes or more 2.615,3.448 3.958,3.667 1.344,0.219 10 false 3 minutes or more 2.375,0.021 6.906,0.604 4.531,0.583 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5.115,3.396 6.302,3.615 1.188,0.219 10 false 3 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0011, P0012, P0021 or P0022.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / DTC [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Advanced Timing Over
(Valve Timing is Out of Specified Range)
Retarded Timing Over
(Valve Timing is Out of Specified Range)
Bank 1 P0011 P0012
Bank 2 P0021 P0022

·

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.

·

If DTC P0011 or P0012 is output, check the right bank VVT system for the intake camshaft circuit (bank 1).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0021 or P0022 is output, check the left bank VVT system for the intake camshaft circuit (bank 2).

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0011, P0012, P0021 or P0022 is output A
P0011, P0012, P0021 or P0022 and other DTCs are output B


HINT:

If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

Powertrain > Engine > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 61 32
Powertrain > Engine > Active Test
Tester Display
Control the VVT Linear (Bank2)
50004 61 31

e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.

OK:
Tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2].

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0011, P0012, P0021 or P0022 is output B


HINT:

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
a.
A301881
0.802,0.844 2.354,0.5 2.354,0.5 2.344,0.854 true 0.771,1.177 2.365,2.26 2.365,2.26 2.438,1.281 true 0.875,3.615 1.781,4.292 1.781,4.292 2.417,3.5 true 1.771,4.281 1.031,3.615 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *A 0.135,2.313 0.448,2.51 0.313,0.198 10 false *B 2.375,2.292 2.688,2.49 0.313,0.198 10 false *a 1.729,4.281 2.042,4.479 0.313,0.198 10 false *a 2.333,0.344 2.646,0.542 0.313,0.198 10 false *a
*A for Bank 1
*B for Bank 2
*a Timing Mark


Remove the cylinder head cover sub-assembly RH and LH.

Click hereEngine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration. If not, turn the crankshaft 1 revolution (360°), and then align the marks as described above.

OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0011, P0012, P0021 or P0022 is output B




A

END

B