Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0100  Mass or Volume Air Flow Circuit  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A122492
1.417,0.5 1.917,1.5 true 2.635,1.063 2.292,1.49 false 4.698,1.26 4.073,2.156 true 5.031,1.552 5.521,2.198 true 0.115,0.302 1.708,0.719 1.594,0.417 10 false Temperature Sensor (Thermistor) 2.167,0.146 2.448,0.365 0.281,0.219 10 false B+ 2.208,0.542 3.573,0.781 1.365,0.24 10 false Power Transistor 2.646,0.958 4.75,1.156 2.104,0.198 10 false Platinum Hot Wire (Heater) 1.667,1.51 1.833,1.719 0.167,0.208 10 false A 2.469,1.51 2.656,1.708 0.188,0.198 10 false B 2.896,1.583 4.083,1.802 1.188,0.219 10 false Output Voltage 5.167,2.188 6.969,2.427 1.802,0.24 10 false Platinum Hot Wire (Heater) 2.896,2.188 5.188,2.448 2.292,0.26 10 false Temperature Sensor (Thermistor)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass or Volume Air Flow Circuit The mass air flow meter circuit is open or shorted for more than 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0102 Mass or Volume Air Flow Circuit Low Input The mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass or Volume Air Flow Circuit High Input The mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the airflow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Airflow Rate (gm/s) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


271.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V, for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0100, P0102 or P0103.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A279104
0.531,2.646 1.052,2.917 0.521,0.271 10 false Battery 1.052,0.604 1.271,0.771 0.219,0.167 10 false 1H 1.594,0.76 1.906,0.927 0.313,0.167 10 false EFI 2.198,1.354 2.656,1.552 0.458,0.198 10 false MAIN 1.875,1.646 3.396,1.854 1.521,0.208 10 false No. 1 Integration Relay 1.104,0.438 1.281,0.604 0.177,0.167 10 false 1 2.917,0.615 3.135,0.781 0.219,0.167 10 false 1J 4.667,0.865 4.885,1.031 0.219,0.167 10 false VG 5.802,0.865 6.021,1.031 0.219,0.167 10 false VG 5.448,0.76 5.646,0.927 0.198,0.167 10 false 30 5.354,0.948 5.729,1.115 0.375,0.167 10 false C129 5.448,1.313 5.656,1.479 0.208,0.167 10 false 29 5.354,1.49 5.781,1.656 0.427,0.167 10 false C129 4.99,0.865 5.125,1.031 0.135,0.167 10 false 3 4.604,1.406 4.906,1.573 0.302,0.167 10 false E2G 5.781,1.406 6.083,1.573 0.302,0.167 10 false E2G 5.5,2.688 5.646,2.854 0.146,0.167 10 false 8 5.354,2.875 5.75,3.042 0.396,0.167 10 false G155 5.781,2.771 6.188,2.938 0.406,0.167 10 false MREL 3.646,1.927 3.958,2.094 0.313,0.167 10 false C36 3.646,2.094 4.99,2.302 1.344,0.208 10 false Mass Air Flow Meter 4.99,1.396 5.125,1.563 0.135,0.167 10 false 2 3.646,0.51 3.865,0.677 0.219,0.167 10 false +B 1.688,1.406 1.906,1.573 0.219,0.167 10 false 1J 1.458,1.396 1.604,1.563 0.146,0.167 10 false 3 2.958,0.427 3.135,0.594 0.177,0.167 10 false 5 2.906,1 3.125,1.167 0.219,0.167 10 false 1J 2.948,0.813 3.125,0.979 0.177,0.167 10 false 2 3.469,0.521 3.646,0.688 0.177,0.167 10 false 1 6.198,3.271 6.563,3.427 0.365,0.156 10 false ECM 0.396,1.865 1.073,2.219 0.677,0.354 10 false BATT 0.396,2.021 0.865,2.219 0.469,0.198 10 false P/I

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0100 and P0102 are output A
DTC P0100 and P0103 are output B




A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
a.

Disconnect the mass air flow meter connector.


b.
A107942
0.354,1.208 0.844,1.5 0.49,0.292 1.198,1.823 1.385,1.49 false 0.042,0.01 0.208,0.177 0.167,0.167 10 false *a 0.479,1.271 0.823,1.458 0.344,0.188 10 false C36 1.021,1.792 1.333,1.958 0.313,0.167 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-3 (VG) - C129-30 (VG) Always Below 1 Ω
C36-2 (E2G) - C129-29 (E2G) Always Below 1 Ω
C36-3 (VG) or C129-30 (VG) - Body ground Always 10 kΩ or higher
C36-2 (E2G) or C129-29 (E2G) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER


c.

Inspect the function of the mass air flow meter.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

v.

Start the engine.


vi.

Check that the reading of the mass air flow meter changes when the engine is raced.

OK:

The reading changes.




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-2 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-2 (E2G) - C129-29 (E2G) Always Below 1 Ω
C36-2 (E2G) or C129-29 (E2G) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-1 (+B) - 1J-5 Always Below 1 Ω
C36-1 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR