Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0110  Intake Air Temperature Circuit Malfunction  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A297777
1.781,2.229 2.198,1.813 false 0.125,0.125 0.594,0.313 0.469,0.188 10 false Fig. 1 0.104,0.406 1.156,0.625 1.052,0.219 10 false Resistance 0.49,0.844 0.802,1.042 0.313,0.198 10 false 30 0.479,1.021 0.792,1.219 0.313,0.198 10 false 20 0.479,1.313 0.792,1.51 0.313,0.198 10 false 10 0.521,1.656 0.677,1.854 0.156,0.198 10 false 5 0.479,3.479 0.771,3.656 0.292,0.177 10 false 0.1 0.479,3.167 0.76,3.375 0.281,0.208 10 false 0.2 0.479,2.823 0.781,2.99 0.302,0.167 10 false 0.3 0.479,2.646 0.938,2.844 0.458,0.198 10 false 0.5 0.521,2.396 0.677,2.594 0.156,0.198 10 false 1 0.521,2.083 0.677,2.281 0.156,0.198 10 false 2 0.521,1.885 0.677,2.083 0.156,0.198 10 false 3 2.24,1.688 3.031,1.917 0.792,0.229 10 false Acceptable 0.76,3.854 1.219,4.052 0.458,0.198 10 false -20 1.219,3.865 1.375,4.063 0.156,0.198 10 false 0 1.521,3.865 1.833,4.063 0.313,0.198 10 false 20 1.844,3.854 2.156,4.052 0.313,0.198 10 false 40 2.188,3.854 2.5,4.052 0.313,0.198 10 false 60 2.542,3.854 2.854,4.052 0.313,0.198 10 false 80 2.865,3.865 3.323,4.063 0.458,0.198 10 false 100 0.74,4.021 1.042,4.292 0.302,0.271 10 false (-4) 1.188,4.021 1.521,4.219 0.333,0.198 10 false 32 1.521,4.021 2.135,4.219 0.615,0.198 10 false 68 1.823,4.021 2.219,4.229 0.396,0.208 10 false 104 2.156,4.01 2.927,4.208 0.771,0.198 10 false 140 2.521,4.021 2.885,4.208 0.365,0.188 10 false 176 2.875,4.021 3.24,4.229 0.365,0.208 10 false 212 1.573,4.313 2.896,4.563 1.323,0.25 10 false Temperature 0.104,0.615 0.531,0.948 0.427,0.333 10 false (kΩ) 2.938,4.229 3.313,4.469 0.375,0.24 10 false ( °C ) 2.948,4.427 3.313,4.635 0.365,0.208 10 false (°F)

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When any of DTCs P0110, P0112 and P0113 are stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0110 Intake Air Temperature Circuit Malfunction An open or short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored
P0112 Intake Air Temperature Circuit Low Input A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Tester Display Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is below 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0110, P0112 or P0113.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A162760
0.26,1.938 0.75,2.094 0.49,0.156 10 C36 0.24,2.115 2.167,2.5 1.927,0.385 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 2.052,0.625 2.385,0.76 0.333,0.135 10 THA 2.167,1.25 2.375,1.396 0.208,0.146 10 E2 2.417,0.625 2.542,0.792 0.125,0.167 10 4 2.417,1.24 2.542,1.406 0.125,0.167 10 5 5.927,2.281 6.396,2.448 0.469,0.167 10 C129 5.292,0.615 5.479,0.771 0.188,0.156 10 22 5.292,1.24 5.479,1.396 0.188,0.156 10 28 5.51,0.625 5.844,0.771 0.333,0.146 10 THA 5.51,1.25 5.74,1.396 0.229,0.146 10 E2 5.938,2.427 6.302,2.604 0.365,0.177 10 ECM 6.229,0.26 6.5,0.427 0.271,0.167 10 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

e.

Read the value displayed on the tester.

Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A303214
0.417,3.344 0.802,3.646 0.385,0.302 1.615,4.042 1.896,3.656 true 2.219,4.021 2.146,3.656 true 0.719,0.313 1.031,0.51 0.313,0.198 10 false *1 2.615,0.292 2.927,0.49 0.313,0.198 10 false *2 2.552,1.073 2.865,1.271 0.313,0.198 10 false THA 2.573,1.51 2.885,1.708 0.313,0.198 10 false E2 0.24,2.51 0.552,2.708 0.313,0.198 10 false *a 0.49,3.417 0.948,3.615 0.458,0.198 10 false C36 1.458,4.052 1.917,4.25 0.458,0.198 10 false THA 2.135,4.052 2.594,4.25 0.458,0.198 10 false E2
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

g.

Read the value displayed on the tester.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-4 (THA) - C129-22 (THA) Always Below 1 Ω
C36-5 (E2) - C129-28 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A211723
0.719,0.281 0.927,0.458 0.208,0.177 10 false *1 2.594,0.26 2.802,0.438 0.208,0.177 10 false *2 2.406,0.99 2.927,1.167 0.521,0.177 10 false THA 2.417,1.448 2.667,1.625 0.25,0.177 10 false E2
*1 Mass Air Flow Meter
*2 ECM


Disconnect the mass air flow meter connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

f.

Read the value displayed on the tester.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-4 (THA) or C129-22 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR