Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil assembly circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil assembly circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil, and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A209715
3.323,8 3.677,8.167 0.354,0.167 10 false ECM 0.323,2.073 2.042,2.281 1.719,0.208 10 false Crankshaft Position Sensor 0.792,4.125 1.573,4.333 0.781,0.208 10 false VVT Sensor 0.208,5.719 2.146,6.49 1.938,0.771 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.188,1.542 3.573,1.729 0.385,0.188 10 false IGT1 3.177,1.979 3.563,2.167 0.385,0.188 10 false IGF1 3.167,2.906 3.552,3.094 0.385,0.188 10 false IGT2 3.167,3.979 3.552,4.167 0.385,0.188 10 false IGT3 3.177,5.052 3.563,5.24 0.385,0.188 10 false IGT4 3.198,6.156 3.583,6.344 0.385,0.188 10 false IGT5 3.188,7.24 3.573,7.427 0.385,0.188 10 false IGT6 5.333,0.771 6.198,1.01 0.865,0.24 10 false from Battery 5.677,1.125 6.854,1.531 1.177,0.406 10 false No. 1 Ignition Coil Assembly 4.438,2.865 5.604,3.281 1.167,0.417 10 false No. 2 Ignition Coil Assembly 5.719,2.094 6.896,2.375 1.177,0.281 10 false No. 1 Spark Plug 5.771,3.313 6.917,3.615 1.146,0.302 10 false No. 2 Spark Plug 4.458,3.958 5.635,4.396 1.177,0.438 10 false No. 3 Ignition Coil Assembly 5.771,4.375 6.917,4.625 1.146,0.25 10 false No. 3 Spark Plug 4.458,5.042 5.625,5.448 1.167,0.406 10 false No. 4 Ignition Coil Assembly 5.771,5.469 6.885,5.708 1.115,0.24 10 false No. 4 Spark Plug 4.458,6.125 5.604,6.594 1.146,0.469 10 false No. 5 Ignition Coil Assembly 5.781,6.542 6.906,6.792 1.125,0.25 10 false No. 5 Spark Plug 4.458,7.219 5.625,7.615 1.167,0.396 10 false No. 6 Ignition Coil Assembly 5.792,7.635 6.917,7.844 1.125,0.208 10 false No. 6 Spark Plug 3.01,7.74 3.417,7.906 0.406,0.167 10 false TACH 1.542,8.219 2.115,8.417 0.573,0.198 10 false to DLC3

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assemblies

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assemblies

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assemblies

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assemblies

·

ECM


Comes on DTC stored
P0355 Ignition Coil "E" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT5 circuit between ignition coil assembly and ECM

·

No. 5 ignition coil assemblies

·

ECM


Comes on DTC stored
P0356 Ignition Coil "F" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT6 circuit between ignition coil assembly and ECM

·

No. 6 ignition coil assemblies

·

ECM


Comes on DTC stored

A112406
0.448,0.302 2.448,0.479 2,0.177 10 false IGT and IGF Signal Waveform 1.125,2.615 2.083,2.813 0.958,0.198 10 false 20 msec./DIV. 2.708,0.729 3.25,0.917 0.542,0.188 10 false 2 V/DIV. 2.906,1.625 3.25,1.813 0.344,0.188 10 false GND 0.24,1.438 0.51,1.625 0.271,0.188 10 false IGT 0.24,2.094 0.5,2.281 0.26,0.188 10 false IGF 2.917,2.469 3.26,2.656 0.344,0.188 10 false GND


Reference: Inspection using an oscilloscope.

While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.

Item Content
Terminal CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
CH2: IGF1 - E1
Equipment Setting 2 V/DIV.
20 msec./DIV.
Condition Cranking


MONITOR DESCRIPTION

A212405
1.781,1.646 2.177,1.823 0.396,0.177 10 false ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 false IGT 2.948,1.729 3.229,1.885 0.281,0.156 10 false IGF 4.156,1.51 4.594,1.75 0.438,0.24 10 false Igniter 5.396,1.344 6.167,1.583 0.771,0.24 10 false Ignition Coil 4.469,2.354 6.167,2.615 1.698,0.26 10 false Ignition Coil Assembly 0.208,3.115 1.146,3.49 0.938,0.375 10 false Ignition Signal (IGT) 1.646,3.542 2.135,3.75 0.49,0.208 10 false Normal 1.385,3.948 2.167,4.177 0.781,0.229 10 false Malfunction 0.26,3.906 1.146,4.771 0.885,0.865 10 false Ignition Confirmation Signal (IGF) 3.635,4.51 4.49,4.74 0.854,0.229 10 false Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353, P0354, P0355 or P0356.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A252545
1.042,3.708 1.323,3.875 0.281,0.167 10 false G9 0.646,4.406 0.75,4.573 0.104,0.167 10 false 5 0.646,3.427 0.75,3.594 0.104,0.167 10 false 6 1.021,3.865 1.656,4.479 0.635,0.615 10 false Ignition Switch Assembly 0.625,4.146 0.948,4.292 0.323,0.146 10 false AM2 0.646,3.677 0.969,3.823 0.323,0.146 10 false IG2 1.948,5.313 2.365,5.677 0.417,0.365 10 false Noise Filter 1.948,5.156 2.333,5.323 0.385,0.167 10 false C133 3.063,8.156 4.875,8.406 1.813,0.25 10 false No. 6 Ignition Coil Assembly 3.052,8 3.417,8.146 0.365,0.146 10 false C144 3.594,7.448 3.833,7.594 0.24,0.146 10 false +B 3.583,7.792 3.917,7.958 0.333,0.167 10 false GND 4.042,7.792 4.302,7.938 0.26,0.146 10 false IGF 3.979,7.448 4.313,7.604 0.333,0.156 10 false IGT6 3.385,7.344 3.49,7.51 0.104,0.167 10 false 1 4.417,7.344 4.531,7.51 0.115,0.167 10 false 3 3.375,7.698 3.479,7.865 0.104,0.167 10 false 4 4.427,7.688 4.552,7.854 0.125,0.167 10 false 2 3.063,6.979 4.865,7.24 1.802,0.26 10 false No. 5 Ignition Coil Assembly 3.063,6.823 3.406,6.969 0.344,0.146 10 false C132 3.594,6.271 3.833,6.417 0.24,0.146 10 false +B 3.583,6.615 3.917,6.781 0.333,0.167 10 false GND 4.042,6.615 4.302,6.76 0.26,0.146 10 false IGF 3.979,6.271 4.313,6.427 0.333,0.156 10 false IGT5 3.385,6.167 3.49,6.333 0.104,0.167 10 false 1 4.417,6.167 4.531,6.333 0.115,0.167 10 false 3 3.375,6.521 3.479,6.688 0.104,0.167 10 false 4 4.427,6.51 4.552,6.677 0.125,0.167 10 false 2 3.063,5.76 4.875,6.021 1.813,0.26 10 false No. 4 Ignition Coil Assembly 3.052,5.604 3.354,5.771 0.302,0.167 10 false C73 3.594,5.052 3.833,5.198 0.24,0.146 10 false +B 3.583,5.396 3.917,5.563 0.333,0.167 10 false GND 4.042,5.396 4.302,5.542 0.26,0.146 10 false IGF 3.979,5.052 4.313,5.208 0.333,0.156 10 false IGT4 3.385,4.938 3.49,5.104 0.104,0.167 10 false 1 4.417,4.948 4.531,5.115 0.115,0.167 10 false 3 3.375,5.302 3.479,5.469 0.104,0.167 10 false 4 4.427,5.292 4.552,5.458 0.125,0.167 10 false 2 3.063,4.469 4.906,4.698 1.844,0.229 10 false No. 3 Ignition Coil Assembly 3.052,4.323 3.396,4.49 0.344,0.167 10 false C72 3.594,3.76 3.833,3.906 0.24,0.146 10 false +B 3.583,4.104 3.917,4.271 0.333,0.167 10 false GND 4.042,4.104 4.302,4.25 0.26,0.146 10 false IGF 3.979,3.76 4.313,3.917 0.333,0.156 10 false IGT3 3.385,3.667 3.49,3.833 0.104,0.167 10 false 1 4.417,3.656 4.531,3.823 0.115,0.167 10 false 3 3.375,4.021 3.479,4.188 0.104,0.167 10 false 4 4.427,4 4.552,4.167 0.125,0.167 10 false 2 3.063,3.167 4.885,3.417 1.823,0.25 10 false No. 2 Ignition Coil Assembly 3.052,3.021 3.365,3.167 0.313,0.146 10 false C71 3.594,2.427 3.833,2.573 0.24,0.146 10 false +B 3.583,2.792 3.917,2.958 0.333,0.167 10 false GND 4.042,2.792 4.302,2.938 0.26,0.146 10 false IGF 3.979,2.438 4.313,2.594 0.333,0.156 10 false IGT2 3.385,2.333 3.49,2.5 0.104,0.167 10 false 1 4.417,2.323 4.531,2.49 0.115,0.167 10 false 3 3.375,2.698 3.479,2.865 0.104,0.167 10 false 4 4.427,2.688 4.552,2.854 0.125,0.167 10 false 2 3.063,1.875 4.875,2.177 1.813,0.302 10 false No. 1 Ignition Coil Assembly 3.052,1.729 3.375,1.885 0.323,0.156 10 false C70 0.844,8.063 1.385,8.354 0.542,0.292 10 false Battery 0.677,6.51 1,6.656 0.323,0.146 10 false AM2 0.677,2.167 1,2.313 0.323,0.146 10 false INJ 3.594,1.135 3.833,1.281 0.24,0.146 10 false +B 3.583,1.5 3.917,1.667 0.333,0.167 10 false GND 4.042,1.5 4.302,1.646 0.26,0.146 10 false IGF 3.979,1.146 4.313,1.302 0.333,0.156 10 false IGT1 5.823,1.417 6.156,1.563 0.333,0.146 10 false IGF1 5.813,1.021 6.146,1.177 0.333,0.156 10 false IGT1 5.813,2.302 6.146,2.458 0.333,0.156 10 false IGT2 5.813,3.635 6.146,3.792 0.333,0.156 10 false IGT3 5.813,4.917 6.146,5.073 0.333,0.156 10 false IGT4 5.813,6.135 6.146,6.292 0.333,0.156 10 false IGT5 5.813,7.313 6.146,7.469 0.333,0.156 10 false IGT6 6.125,8.219 6.479,8.385 0.354,0.167 10 false ECM 6.125,8.063 6.479,8.229 0.354,0.167 10 false C129 3.385,1.042 3.49,1.208 0.104,0.167 10 false 1 4.417,1.031 4.531,1.198 0.115,0.167 10 false 3 3.375,1.406 3.479,1.573 0.104,0.167 10 false 4 4.427,1.396 4.552,1.563 0.125,0.167 10 false 2 5.604,1.021 5.708,1.177 0.104,0.156 10 false 8 5.604,2.313 5.729,2.469 0.125,0.156 10 false 9 5.552,3.635 5.74,3.802 0.188,0.167 10 false 10 5.552,1.406 5.74,1.563 0.188,0.156 10 false 24 5.563,4.917 5.76,5.073 0.198,0.156 10 false 11 5.521,6.135 5.719,6.292 0.198,0.156 10 false 12 5.521,7.323 5.719,7.479 0.198,0.156 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
A203962
0.094,0.604 0.458,0.875 0.365,0.271 0.521,0.604 0.885,0.875 0.365,0.271 0.094,0.927 0.458,1.198 0.365,0.271 0.521,0.927 0.885,1.198 0.365,0.271 0.083,1.26 0.448,1.531 0.365,0.271 0.51,1.25 0.875,1.521 0.365,0.271 1.26,1.167 1.063,1.719 false 2.156,1.198 2.365,1.688 false 0.188,0.656 0.531,0.823 0.344,0.167 10 false C70 0.594,0.656 0.875,0.844 0.281,0.188 10 false C73 0.167,0.99 0.615,1.167 0.448,0.177 10 false C71 0.552,1 1.042,1.188 0.49,0.188 10 false C132 0.135,1.323 0.438,1.49 0.302,0.167 10 false C72 0.542,1.333 0.885,1.521 0.344,0.188 10 false C144 0.229,0.083 0.417,0.271 0.188,0.188 10 false *a 0.938,1.719 1.146,1.906 0.208,0.188 10 false +B 2.24,1.729 2.594,1.875 0.354,0.146 10 false GND
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C70-4 (GND) - Body ground Always Below 1 Ω
C71-4 (GND) - Body ground Always Below 1 Ω
C72-4 (GND) - Body ground Always Below 1 Ω
C73-4 (GND) - Body ground Always Below 1 Ω
C132-4 (GND) - Body ground Always Below 1 Ω
C144-4 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C70-1 (+B) - C70-4 (GND) Ignition switch ON 11 to 14 V
C71-1 (+B) - C71-4 (GND) Ignition switch ON 11 to 14 V
C72-1 (+B) - C72-4 (GND) Ignition switch ON 11 to 14 V
C73-1 (+B) - C73-4 (GND) Ignition switch ON 11 to 14 V
C132-1 (+B) - C132-4 (GND) Ignition switch ON 11 to 14 V
C144-1 (+B) - C144-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C70-2 (IGF) - C129-24 (IGF1) Always Below 1 Ω
C71-2 (IGF) - C129-24 (IGF1) Always Below 1 Ω
C72-2 (IGF) - C129-24 (IGF1) Always Below 1 Ω
C73-2 (IGF) - C129-24 (IGF1) Always Below 1 Ω
C132-2 (IGF) - C129-24 (IGF1) Always Below 1 Ω
C144-2 (IGF) - C129-24 (IGF1) Always Below 1 Ω
C70-3 (IGT1) - C129-8 (IGT1) Always Below 1 Ω
C71-3 (IGT2) - C129-9 (IGT2) Always Below 1 Ω
C72-3 (IGT3) - C129-10 (IGT3) Always Below 1 Ω
C73-3 (IGT4) - C129-11 (IGT4) Always Below 1 Ω
C132-3 (IGT5) - C129-12 (IGT5) Always Below 1 Ω
C144-3 (IGT6) - C129-13 (IGT6) Always Below 1 Ω
C70-2 (IGF) or C129-24 (IGF1) - Body ground Always 10 kΩ or higher
C71-2 (IGF) or C129-24 (IGF1) - Body ground Always 10 kΩ or higher
C72-2 (IGF) or C129-24 (IGF1) - Body ground Always 10 kΩ or higher
C73-2 (IGF) or C129-24 (IGF1) - Body ground Always 10 kΩ or higher
C132-2 (IGF) or C129-24 (IGF1) - Body ground Always 10 kΩ or higher
C144-2 (IGF) or C129-24 (IGF1) - Body ground Always 10 kΩ or higher
C70-3 (IGT1) or C129-8 (IGT1) - Body ground Always 10 kΩ or higher
C71-3 (IGT2) or C129-9 (IGT2) - Body ground Always 10 kΩ or higher
C72-3 (IGT3) or C129-10 (IGT3) - Body ground Always 10 kΩ or higher
C73-3 (IGT4) or C129-11 (IGT4) - Body ground Always 10 kΩ or higher
C132-3 (IGT5) or C129-12 (IGT5) - Body ground Always 10 kΩ or higher
C144-3 (IGT6) or C129-13 (IGT6) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Shuffle arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not shuffle the connectors.



e.

Perform a simulation test.


f.

Check the output DTCs displayed on the tester.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
Same DTC is output A
Different ignition coil DTC is output B




A

B