Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A179391
0.958,1.542 1.167,1.135 1.167,1.135 1.271,1.135 false 1.521,1.948 1.823,2.198 0.302,0.25 10 false [A] 2.844,1.948 3.115,2.177 0.271,0.229 10 false [B] 3.896,3 4.167,3.208 0.271,0.208 10 false [C] 4.573,1.333 4.833,1.552 0.26,0.219 10 false [D] 5.094,3 5.385,3.26 0.292,0.26 10 false [E] 0.51,2.073 0.948,2.302 0.438,0.229 10 false Idling 4.229,2.521 5.01,2.833 0.781,0.313 10 false 10 minutes or more 2.594,2.521 3.385,2.885 0.792,0.365 10 false 15 minutes or more 1.302,2.552 2.094,2.792 0.792,0.24 10 false Warming up 1.375,1.052 3.406,1.479 2.031,0.427 10 false Between 40 km/h and 60 km/h (25 mph and 37 mph) 0.125,0.448 1.115,0.719 0.99,0.271 10 false Vehicle Speed

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0443.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



13.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

A279110
4.448,1.271 4.875,1.438 0.427,0.167 10 C143 4.448,1.396 5.188,1.573 0.74,0.177 10 Purge VSV 4.354,0.854 4.469,1.021 0.115,0.167 10 1 5.115,0.865 5.229,1.031 0.115,0.167 10 2 5.531,0.979 5.927,1.135 0.396,0.156 10 C129 5.625,0.771 5.823,0.938 0.198,0.167 10 34 5.958,0.875 6.302,1.042 0.344,0.167 10 PRG 5.531,2.135 5.906,2.292 0.375,0.156 10 G155 5.677,1.938 5.813,2.104 0.135,0.167 10 8 5.938,2.01 6.385,2.177 0.448,0.167 10 MREL 3.313,0.771 3.427,0.938 0.115,0.167 10 5 3.271,0.99 3.5,1.156 0.229,0.167 10 1J 3.302,1.271 3.427,1.448 0.125,0.177 10 2 3.271,1.479 3.5,1.646 0.229,0.167 10 1J 1.615,0.802 1.729,0.969 0.115,0.167 10 1 1.563,0.979 1.792,1.146 0.229,0.167 10 1H 1.615,1.292 1.729,1.458 0.115,0.167 10 3 1.583,1.479 1.813,1.646 0.229,0.167 10 1J 2,1.115 2.271,1.281 0.271,0.167 10 EFI 2.583,1.802 3.01,1.969 0.427,0.167 10 MAIN 1.76,2.156 3.281,2.344 1.521,0.188 10 No. 1 Integration Relay 0.396,1.635 0.792,1.979 0.396,0.344 10 BATT P/I 0.531,2.75 1.021,2.948 0.49,0.198 10 Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A080362
0.885,0.438 1.104,0.688 0.219,0.25 10 false *a 2.521,0.438 2.729,0.688 0.208,0.25 10 false *b 1.479,1.531 1.865,1.729 0.385,0.198 10 false *c
*a VSV is ON
*b VSV is OFF
*c Air


Connect the intelligent tester to the DLC3.


b.

Remove the vacuum hose of the purge VSV from the charcoal canister.


c.

Start the engine and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 61 6

e.

When the purge VSV is operated using the tester, check whether the purge VSV applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV is ON Suction applied
VSV is OFF No suction applied



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
a.
A241839
0.646,1.104 1.063,1.354 0.417,0.25 0.698,1.146 1.042,1.313 0.344,0.167 10 C143 0.167,0.083 0.406,0.281 0.24,0.198 10 *a
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C143-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the terminals of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
C143-2 - C129-34 (PRG) Always Below 1 Ω
C143-2 or C129-34 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


g.

Idle the engine for 15 minutes or more.


h.

Turn the tester on.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P0443.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0443 is output)
B


HINT:

If the judgment result shows INCOMPLETE or N/A, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes and check the DTC judgment result again.




A

B

6.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C143-1 - 1J-5 Always Below 1 Ω
C143-1 or 1J-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR