Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter assembly, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A112414
1.635,1.906 2.521,2.156 0.885,0.25 10 false Transmission 2.771,1.906 4.677,2.156 1.906,0.25 10 false Combination Meter Assembly 5.146,1.906 5.531,2.135 0.385,0.229 10 false ECM 2.427,0.427 3.448,0.708 1.021,0.281 10 false 4 Pulse Signal 4.094,0.427 5.104,0.646 1.01,0.219 10 false 4 Pulse Signal

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor Malfunction While vehicle is being driven, no vehicle speed sensor signal input to ECM
(2 trip detection logic)
·

Open or short in speed sensor circuit

·

Vehicle speed sensor

·

Combination meter assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the park/neutral position switch is OFF while the vehicle speed signal from the transmission indicates a speed of 9 km/h (6 mph) or more. If there is no vehicle speed signal from the combination meter for 5 seconds when the vehicle is being driven, the ECM determines this to be a malfunction of the vehicle speed sensor. The ECM then illuminates the MIL and stores the DTC.

CONFIRMATION DRIVING PATTERN

A232052
0.656,0.823 1.854,1.052 1.198,0.229 10 false 24 km/h (15 mph) 1.417,2 1.844,2.271 0.427,0.271 10 false Idling 0.615,2.344 1.885,2.552 1.271,0.208 10 false Ignition Switch ON 2.385,2.219 2.667,2.49 0.281,0.271 10 false [A] 4.708,0.417 4.948,0.646 0.24,0.229 10 false [B] 6.25,3.229 6.521,3.469 0.271,0.24 10 false [C] 3.969,3.021 5.906,3.26 1.938,0.24 10 false Total of 30 seconds or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0500.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A206532
6.281,0.615 6.531,0.771 0.25,0.156 10 false 5 V 5.521,0.885 5.844,1.042 0.323,0.156 10 false SPD 5.354,0.938 5.49,1.094 0.135,0.156 10 false 8 6.021,1.865 6.448,2.042 0.427,0.177 10 false G154 6.042,2.01 6.396,2.177 0.354,0.167 10 false ECM 4.344,1.052 4.552,1.198 0.208,0.146 10 false 2P 3.438,1.052 3.656,1.198 0.219,0.146 10 false 2Q 4.344,0.865 4.542,1.021 0.198,0.156 10 false 26 3.438,0.865 3.615,1.021 0.177,0.156 10 false 26 2.594,0.938 2.719,1.094 0.125,0.156 10 false 6 1.094,1.052 1.385,1.208 0.292,0.156 10 false SI 1.25,1.896 1.635,2.073 0.385,0.177 10 false G19 1.24,2.063 2.417,2.438 1.177,0.375 10 false Combination Meter Assembly 0.104,2.708 1.688,3.073 1.583,0.365 10 false from Speed Sensor 0.927,1.052 1.052,1.208 0.125,0.156 10 false 5 2.313,0.938 2.604,1.094 0.292,0.156 10 false +S 3.5,1.458 4.229,1.635 0.729,0.177 10 false Driver Side 3.5,1.635 4.49,1.823 0.99,0.188 10 false Junction Block

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Drive the vehicle.


f.

Read the value displayed on the intelligent tester.

OK:

Vehicle speeds displayed on intelligent tester and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-6 (+S) - G154-8 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR