Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the ETCS and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the ETCS itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The ETCS does not use a throttle cable.


A112629
0.969,1.104 1.052,1.146 1.052,1.146 0.969,1.188 false 0.969,1.875 1.052,1.917 1.052,1.917 0.969,1.958 false 0.115,1.813 0.917,2.063 0.802,0.25 10 false from Battery 0.823,3.573 2.042,3.771 1.219,0.198 10 false Throttle Actuator 1.229,2 2.167,2.198 0.938,0.198 10 false ETCS 5.594,4.24 6.042,4.438 0.448,0.198 10 false ECM 4.76,1.74 5.208,1.938 0.448,0.198 10 false +BM 4.76,3.792 5.281,3.99 0.521,0.198 10 false ME01 4.76,2.469 5.073,2.667 0.313,0.198 10 false M+ 4.76,3.115 5.073,3.313 0.313,0.198 10 false M- 5.938,2.438 6.49,3.208 0.552,0.771 10 false Throttle Actuator Control Circuit 4.76,0.958 5.208,1.156 0.448,0.198 10 false +B 0.271,0.979 0.823,1.365 0.552,0.385 10 false from EFI Relay 5.906,0.917 6.792,1.438 0.885,0.521 10 false Power Source Circuit for CPU

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2118 Throttle Actuator Control Motor Current Range / Performance An open in the ETCS power source (+BM) circuit (1 trip detection logic).
·

Open in ETCS power source circuit

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

A199315
0.979,0.583 1.656,0.875 0.677,0.292 10 false 3000 rpm 1.24,1.969 1.656,2.24 0.417,0.271 10 false Idling 0.438,2.26 1.656,2.5 1.219,0.24 10 false Ignition Switch ON 3.146,2.25 4.74,2.5 1.594,0.25 10 false Approximately 5 seconds 3.469,2.802 4.875,3.031 1.406,0.229 10 false 16 seconds or more 2.031,2.354 2.271,2.615 0.24,0.26 10 false [A] 6.01,3.24 6.344,3.521 0.333,0.281 10 false [C] 4.604,0.438 4.896,0.708 0.292,0.271 10 false [B]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine.

7.

Slowly depress the accelerator pedal, raise the engine speed to approximately 3000 rpm over approximately 5 seconds, and then idle the engine [B].

8.

Check that 16 seconds or more have elapsed since the engine was started.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2118.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again and, if necessary, drive the vehicle for a period of time.




FAIL-SAFE

When this DTC, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A279111
5.708,4.75 6.073,4.906 0.365,0.156 10 false ECM 5.49,1.625 6.563,1.979 1.073,0.354 10 false Throttle Actuator Control Circuit 4.958,0.729 5.313,0.885 0.354,0.156 10 false +BM 2.51,1.375 2.75,1.542 0.24,0.167 10 false M+ 2.51,2.219 2.75,2.385 0.24,0.167 10 false M- 4.969,1.375 5.208,1.542 0.24,0.167 10 false M+ 4.969,2.219 5.208,2.385 0.24,0.167 10 false M- 4.958,2.938 5.333,3.094 0.375,0.156 10 false GE01 4.969,3.5 5.177,3.656 0.208,0.156 10 false E1 4.969,4 5.365,4.167 0.396,0.167 10 false ME01 4.542,1.469 4.927,1.625 0.385,0.156 10 false C129 4.552,0.813 4.958,0.969 0.406,0.156 10 false G155 4.688,0.646 4.823,0.802 0.135,0.156 10 false 7 4.688,3.344 4.875,3.5 0.188,0.156 10 false 1 4.688,3.833 4.823,3.99 0.135,0.156 10 false 3 4.688,1.313 4.885,1.469 0.198,0.156 10 false 5 4.688,2.146 4.813,2.302 0.125,0.156 10 false 4 4.646,2.781 4.844,2.938 0.198,0.156 10 false 17 3.802,2.667 4.375,2.833 0.573,0.167 10 false Shielded 2.792,1.375 2.906,1.531 0.115,0.156 10 false 2 2.792,2.229 2.906,2.385 0.115,0.156 10 false 1 1.813,2.719 2.135,2.875 0.323,0.156 10 false C57 1.813,2.875 2.875,3.052 1.063,0.177 10 false Throttle Actuator 1.146,0.948 1.563,1.115 0.417,0.167 10 false ETCS 0.615,4.094 1.177,4.281 0.563,0.188 10 false Battery 4.552,4.01 4.938,4.167 0.385,0.156 10 false C130 4.552,2.313 4.927,2.469 0.375,0.156 10 false C129 4.552,2.938 4.917,3.094 0.365,0.156 10 false C129 4.552,3.5 4.938,3.656 0.385,0.156 10 false C131

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / +BM Voltage.

Powertrain > Engine > Data List
Tester Display
+BM Voltage
50003 61 123

e.

Read the value displayed on the tester.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.
A253414
2.677,0.625 3.104,0.875 0.427,0.25 0.979,0.625 1.406,0.875 0.427,0.25 1.49,0.625 1.917,0.875 0.427,0.25 1.49,0.625 1.917,0.875 0.427,0.25 1.146,2.135 0.698,2.927 true 2.625,2.135 2.427,2.938 true 1.958,2.125 1.521,2.927 true 0.25,2.958 0.885,3.188 0.635,0.229 10 false 3 (ME01) 2.073,2.958 2.667,3.198 0.594,0.24 10 false 7 (+BM) 1.229,2.958 1.865,3.188 0.635,0.229 10 false 1 (E1) 0.25,0.125 0.469,0.313 0.219,0.188 10 false *a 2.74,0.667 3.188,0.927 0.448,0.26 10 false G155 1.042,0.667 1.406,0.844 0.365,0.177 10 false C130 1.542,0.667 2.031,0.938 0.49,0.271 10 false C131
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G155-7 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C130-3 (ME01) - Body ground Always Below 1 Ω
C131-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR