Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.

The accelerator pedal position sensor is mounted on the accelerator pedal rod assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


A115889
0.979,2.313 1.396,1.521 true 0.979,3.188 1.021,3.51 true 0.958,2.573 0.646,1.427 true 0.906,2.854 0.479,3.354 true 0.073,3.844 2.281,4.042 2.208,0.198 10 false Accelerator Pedal Position Sensor 1.438,1.396 2.021,1.615 0.583,0.219 10 false Magnet 2.323,3.677 2.667,3.875 0.344,0.198 10 false ECM 3.906,2.135 4.323,2.333 0.417,0.198 10 false 3.988 3.906,2.333 4.333,2.531 0.427,0.198 10 false 3.188 4.042,2.844 4.302,3.042 0.26,0.198 10 false 1.6 4.042,3.052 4.271,3.25 0.229,0.198 10 false 0.8 4.177,1.948 4.313,2.146 0.135,0.198 10 false 5 1.708,1.771 2.083,2.01 0.375,0.24 10 false VPA 1.719,2.083 2.125,2.302 0.406,0.219 10 false EPA 1.719,2.406 2.167,2.615 0.448,0.208 10 false VCPA 1.729,2.688 2.208,2.896 0.479,0.208 10 false VPA2 1.719,3.01 2.198,3.208 0.479,0.198 10 false EPA2 1.719,3.333 2.167,3.542 0.448,0.208 10 false VCP2 4.781,3.573 5.708,3.771 0.927,0.198 10 false Usable Range 4.375,3.854 6.833,4.052 2.458,0.198 10 false Accelerator Pedal Opening Angle (°) 0.292,4.958 2.75,5.135 2.458,0.177 10 false *1: Accelerator Pedal Fully Released 0.292,5.302 2.75,5.5 2.458,0.198 10 false *2: Accelerator Pedal Fully Depressed 3.104,0.896 4.333,1.406 1.229,0.51 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.438,1.552 4.635,1.75 0.198,0.198 10 false *1 4.479,3.552 4.677,3.75 0.198,0.198 10 false 0 6.313,3.375 6.51,3.573 0.198,0.198 10 false 25 5.865,1.563 6.063,1.76 0.198,0.198 10 false *2 0.833,3.51 1.354,3.688 0.521,0.177 10 false Magnet 0.094,1.354 0.656,1.5 0.563,0.146 10 false IC No. 1 0.354,3.354 0.927,3.5 0.573,0.146 10 false IC No. 2 5.844,3.563 6.156,3.76 0.313,0.198 10 false 15.9

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input VPA is 0.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

Open in EPA circuit

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input VPA2 is 0.5 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.2 V and 3.45 V.
·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

Open in EPA2 circuit

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.2 V or less and VPA2 is 0.5 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal position sensor (built into accelerator pedal rod assembly)

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accelerator Position No.1 and Accelerator Position No.2.

Trouble Area Accelerator Position No. 1
When Accelerator Pedal Released
Accelerator Position No. 2
When Accelerator Pedal Released
Accelerator Position No. 1
When Accelerator Pedal Depressed
Accelerator Position No. 2
When Accelerator Pedal Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.9 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 4.9 V 4.5 to 4.9 V 4.5 to 4.9 V 4.5 to 4.9 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.9 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is below the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA drops below 0.2 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

A199317
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.094 1.74,0.323 1.615,0.229 10 false Accelerator Pedal State 0.865,0.417 1.594,0.635 0.729,0.219 10 false Depressed 0.948,0.906 1.583,1.156 0.635,0.25 10 false Released 0.438,2.385 1.646,2.625 1.208,0.24 10 false Ignition Switch ON 2.094,2.49 2.375,2.729 0.281,0.24 10 false [A] 4.385,3.427 4.677,3.656 0.292,0.229 10 false [C] 5.292,1.719 5.979,1.948 0.688,0.229 10 false Released 2.875,3.063 3.552,3.24 0.677,0.177 10 false 5 seconds 3.01,1.219 3.76,1.469 0.75,0.25 10 false Depressed 3.865,1.125 4.188,1.406 0.323,0.281 10 false [B] 2.594,2.031 3.229,2.229 0.635,0.198 10 false Released

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.




FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 are stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue to be driven. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A149601
0.292,3.188 2.792,3.573 2.5,0.385 10 false Accelerator Pedal Position Sensor (built into Accelerator Pedal Rod Assembly) 1.552,0.531 2.021,0.74 0.469,0.208 10 false VPA 1.563,0.969 2.031,1.177 0.469,0.208 10 false EPA 1.479,1.375 2.073,1.583 0.594,0.208 10 false VCPA 1.51,1.792 2.104,2 0.594,0.208 10 false VPA2 1.51,2.219 2.104,2.427 0.594,0.208 10 false EPA2 1.51,2.646 2.104,2.854 0.594,0.208 10 false VCP2 5.604,0.458 6,0.667 0.396,0.208 10 false VPA 5.344,0.448 5.521,0.656 0.177,0.208 10 false 18 5.333,0.865 5.51,1.073 0.177,0.208 10 false 20 5.323,1.292 5.5,1.5 0.177,0.208 10 false 26 5.313,1.708 5.49,1.917 0.177,0.208 10 false 19 5.313,2.135 5.49,2.344 0.177,0.208 10 false 21 5.302,2.542 5.479,2.75 0.177,0.208 10 false 27 5.604,0.885 6,1.094 0.396,0.208 10 false EPA 5.604,1.292 6.052,1.5 0.448,0.208 10 false VCPA 5.604,1.708 6.052,1.917 0.448,0.208 10 false VPA2 5.615,2.115 6.052,2.323 0.438,0.208 10 false EPA2 5.625,2.542 6.219,2.75 0.594,0.208 10 false VCP2 1.99,0.448 2.198,0.656 0.208,0.208 10 false 6 1.99,0.854 2.198,1.063 0.208,0.208 10 false 5 1.99,1.271 2.198,1.479 0.208,0.208 10 false 4 1.99,1.698 2.198,1.906 0.208,0.208 10 false 3 1.99,2.115 2.198,2.323 0.208,0.208 10 false 2 2,2.542 2.208,2.75 0.208,0.208 10 false 1 5.99,3.198 6.385,3.396 0.396,0.198 10 false ECM 5.979,3.042 6.385,3.24 0.406,0.198 10 false G155 0.344,3.031 0.625,3.219 0.281,0.188 10 false G6

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the accelerator pedal position sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR)
a.
A208621
0.67,1.751 0.875,1.926 0.205,0.175 10 *a 2.612,1.751 2.803,1.926 0.191,0.175 10 *b
*a Depressed
*b Released


Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Powertrain > Engine > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 61 128,129

d.

Read the value displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2 Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V More than 0.02 V
Depressed 2.6 to 4.5 V 3.4 to 4.9 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ROD ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ROD ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal rod assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-6 (VPA) - G155-18 (VPA) Always Below 1 Ω
G6-5 (EPA) - G155-20 (EPA) Always Below 1 Ω
G6-4 (VCPA) - G155-26 (VCPA) Always Below 1 Ω
G6-3 (VPA2) - G155-19 (VPA2) Always Below 1 Ω
G6-2 (EPA2) - G155-21 (EPA2) Always Below 1 Ω
G6-1 (VCP2) - G155-27 (VCP2) Always Below 1 Ω
G6-6 (VPA) or G155-18 (VPA) - Body ground Always 10 kΩ or higher
G6-5 (EPA) or G155-20 (EPA) - Body ground Always 10 kΩ or higher
G6-4 (VCPA) or G155-26 (VCPA) - Body ground Always 10 kΩ or higher
G6-3 (VPA2) or G155-19 (VPA2) - Body ground Always 10 kΩ or higher
G6-2 (EPA2) or G155-21 (EPA2) - Body ground Always 10 kΩ or higher
G6-1 (VCP2) or G155-27 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (VCPA AND VCP2 VOLTAGE)
a.
A200902
0.615,0.979 0.969,1.25 0.354,0.271 0.969,1.573 1.344,1.094 false 1.49,1.594 1.552,1.115 false 1.927,1.594 1.781,1.125 false 2.417,1.594 1.948,1.115 false 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 0.708,1.031 1.021,1.229 0.313,0.198 10 false G6 0.729,1.594 1.177,1.792 0.448,0.198 10 false VCP2 1.281,1.615 1.74,1.813 0.458,0.198 10 false EPA2 1.802,1.615 2.271,1.813 0.469,0.198 10 false VCPA 2.344,1.615 2.656,1.813 0.313,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Rod Assembly)


Disconnect the accelerator pedal rod assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-4 (VCPA) - G6-5 (EPA) Ignition switch ON 4.5 to 5.5 V
G6-1 (VCP2) - G6-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Result Proceed to
P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output A
DTC is not output B




A

B

END