Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)  P2241  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)  P2242  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  P2255  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)  P2256  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

HINT:

Although the DTC titles include oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A178930
1.615,2.927 1,2.427 false 1.771,2.917 1.969,2.635 false 2.865,2.104 3.281,0.729 false 3.01,2.094 3.198,1.542 false 3.146,2.156 3.729,2.01 false 2.938,2.677 3.385,2.521 3.385,2.521 2.781,2.813 false 3,2.896 3.427,3.208 false 1,2.427 0.906,2.427 false 1.969,2.635 2.042,2.635 false 3.427,3.208 3.51,3.208 false 3.396,2.521 3.5,2.521 false 3.063,0.729 3.281,0.729 false 3.198,1.542 3.333,1.542 false 0.208,3.125 1.083,3.292 0.875,0.167 10 false Exhaust Gas 0.354,2.365 0.938,2.531 0.583,0.167 10 false Element 2.073,2.563 2.51,2.719 0.438,0.156 10 false Cover 1.917,3.417 2.063,3.604 0.146,0.188 10 false A 1.25,3.417 1.396,3.604 0.146,0.188 10 false A 2.427,3.458 3.594,3.625 1.167,0.167 10 false A-A Cross Section 3.531,3.135 4.563,3.313 1.031,0.177 10 false Atmospheric Air 3.531,2.448 4.729,2.615 1.198,0.167 10 false Platinum Electrode 3.792,1.938 4.271,2.135 0.479,0.198 10 false Heater 3.365,1.479 3.906,1.708 0.542,0.229 10 false Alumina 1.865,0.594 3.073,0.969 1.208,0.375 10 false Solid Electrolyte (Zirconia Element) 5.615,3.49 6.469,3.646 0.854,0.156 10 false Air-fuel Ratio 4.604,0.75 6.135,1.094 1.531,0.344 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.281,3.115 5.479,3.271 0.198,0.156 10 false 12 5.5,3.115 5.698,3.271 0.198,0.156 10 false 13 5.708,3.115 5.906,3.271 0.198,0.156 10 false 14 5.938,3.115 6.135,3.271 0.198,0.156 10 false 15 6.146,3.115 6.344,3.271 0.198,0.156 10 false 16 6.354,3.115 6.552,3.271 0.198,0.156 10 false 17 6.583,3.115 6.781,3.271 0.198,0.156 10 false 18 4.917,2.844 5.156,3 0.24,0.156 10 false 2.0 4.917,2.531 5.156,2.688 0.24,0.156 10 false 2.5 4.917,2.229 5.156,2.385 0.24,0.156 10 false 3.0 4.917,1.927 5.156,2.083 0.24,0.156 10 false 3.5 4.917,1.625 5.156,1.781 0.24,0.156 10 false 4.0

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 1 sensor 1) circuit

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) Any of the following conditions are met (2 trip detection logic):
·

The air fuel ratio sensor output drops while the engine is running.

·

The voltage at terminal A1A+ is 0.5 V or less.

·

The voltage difference between terminals A1A+ and A1A- is 0.1 V or less.


·

Open or short in air fuel ratio sensor (for bank 1 sensor 1) circuit

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 1 sensor 1) circuit

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) An open in the circuit between terminals A2A+ and A2A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 2 sensor 1) circuit

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) Any of the following conditions are met (2 trip detection logic):
·

The air fuel ratio sensor output drops while the engine is running.

·

The voltage at terminal A2A+ is 0.5 V or less.

·

The voltage difference between terminals A2A+ and A2A- is 0.1 V or less.


·

Open or short in air fuel ratio sensor (for bank 2 sensor 1) circuit

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) The A2A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 2 sensor 1) circuit

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) The A1A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 1 sensor 1) circuit

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) The A1A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 1 sensor 1) circuit

·

Air fuel ratio sensor (for bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) The A2A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 2 sensor 1) circuit

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) The A2A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (for bank 2 sensor 1) circuit

·

Air fuel ratio sensor (for bank 2 sensor 1)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs are stored when there is an open or short in the air fuel ratio sensor circuit, or if air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the MIL will be illuminated and a DTC will be stored.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine and wait for 5 minutes or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A279112
0.688,6.74 1.177,6.969 0.49,0.229 10 false Battery 1.208,5.188 1.594,5.531 0.385,0.344 10 false BATT P/I 1.917,3.5 2.333,3.677 0.417,0.177 10 false MAIN 1.198,4.042 1.469,4.188 0.271,0.146 10 false EFI 3.979,0.865 4.177,1.052 0.198,0.188 10 false +B 3.948,1.51 4.344,1.698 0.396,0.188 10 false A1A- 4.344,0.865 4.729,1.052 0.385,0.188 10 false HA1A 4.354,1.51 4.75,1.698 0.396,0.188 10 false A1A+ 3.958,3.333 4.156,3.521 0.198,0.188 10 false +B 3.948,3.958 4.333,4.146 0.385,0.188 10 false A2A- 4.344,3.323 4.74,3.51 0.396,0.188 10 false HA2A 4.354,3.969 4.75,4.156 0.396,0.188 10 false A2A+ 3.542,4.469 4.906,4.865 1.365,0.396 10 false Air Fuel Ratio Sensor (for Bank 2 Sensor 1) 3.531,2.01 4.896,2.375 1.365,0.365 10 false Air Fuel Ratio Sensor (for Bank 1 Sensor 1) 5.25,5.51 5.51,5.667 0.26,0.156 10 false * 5.25,3.052 5.51,3.208 0.26,0.156 10 false * 6.24,6.573 6.594,6.729 0.354,0.156 10 false ECM 6.01,6 6.417,6.156 0.406,0.156 10 false MREL 6,0.885 6.406,1.042 0.406,0.156 10 false HA1A 6.01,2.594 6.365,2.75 0.354,0.156 10 false A1A- 5.573,2.719 5.958,2.865 0.385,0.146 10 false C130 5.667,2.542 5.844,2.688 0.177,0.146 10 false 30 6.01,1.552 6.417,1.708 0.406,0.156 10 false A1A+ 6.01,3.344 6.417,3.5 0.406,0.156 10 false HA2A 6.01,5.042 6.417,5.198 0.406,0.156 10 false A2A- 6.01,4.021 6.417,4.177 0.406,0.156 10 false A2A+ 1.469,7.281 2.24,7.438 0.771,0.156 10 false *: Shielded 3.531,1.865 3.906,2.01 0.375,0.146 10 false C150 4.802,4 4.896,4.146 0.094,0.146 10 false 3 4.802,3.323 4.896,3.469 0.094,0.146 10 false 1 3.771,4.021 3.865,4.167 0.094,0.146 10 false 4 3.771,3.323 3.865,3.469 0.094,0.146 10 false 2 4.781,1.552 4.875,1.698 0.094,0.146 10 false 3 4.781,0.875 4.875,1.021 0.094,0.146 10 false 1 3.771,1.552 3.865,1.698 0.094,0.146 10 false 4 3.771,0.875 3.865,1.021 0.094,0.146 10 false 2 3.542,4.313 3.917,4.458 0.375,0.146 10 false C148 0.854,4.479 0.948,4.625 0.094,0.146 10 false 1 0.833,3.01 0.927,3.156 0.094,0.146 10 false 5 0.281,0.865 0.375,1.01 0.094,0.146 10 false 3 0.281,1.708 0.375,1.854 0.094,0.146 10 false 5 1.188,0.865 1.281,1.01 0.094,0.146 10 false 2 1.188,1.708 1.281,1.854 0.094,0.146 10 false 1 1.906,3.01 2,3.156 0.094,0.146 10 false 3 1.906,4.479 2,4.625 0.094,0.146 10 false 2 5.573,5.167 5.958,5.313 0.385,0.146 10 false C130 5.573,4.135 5.958,4.281 0.385,0.146 10 false C130 5.583,3.427 5.969,3.573 0.385,0.146 10 false C130 5.583,1.677 5.969,1.823 0.385,0.146 10 false C130 5.583,0.979 5.969,1.125 0.385,0.146 10 false C130 5.573,5.99 5.948,6.135 0.375,0.146 10 false G155 5.708,3.26 5.885,3.406 0.177,0.146 10 false 1 5.667,3.958 5.844,4.104 0.177,0.146 10 false 23 5.667,4.99 5.844,5.135 0.177,0.146 10 false 31 5.708,5.813 5.833,5.958 0.125,0.146 10 false 8 5.708,0.792 5.833,0.938 0.125,0.146 10 false 2 5.667,1.49 5.844,1.635 0.177,0.146 10 false 22 1.396,1.292 1.667,1.469 0.271,0.177 10 false A/F 0.51,5.25 0.781,5.427 0.271,0.177 10 false A/F 1.604,4.479 1.865,4.635 0.26,0.156 10 false 1J 1.604,3.01 1.865,3.167 0.26,0.156 10 false 1J 1.031,3.01 1.292,3.167 0.26,0.156 10 false 1J 1.031,4.479 1.292,4.635 0.26,0.156 10 false 1H 1.823,4.729 2.604,5.302 0.781,0.573 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [AFS Voltage B1S1 and AFS Voltage B2S1] (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Bank 1 refers to the bank that includes No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C150-1 (HA1A) - C130-2 (HA1A) Always Below 1 Ω
C150-3 (A1A+) - C130-22 (A1A+) Always Below 1 Ω
C150-4 (A1A-) - C130-30 (A1A-) Always Below 1 Ω
C148-1 (HA2A) - C130-1 (HA2A) Always Below 1 Ω
C148-3 (A2A+) - C130-23 (A2A+) Always Below 1 Ω
C148-4 (A2A-) - C130-31 (A2A-) Always Below 1 Ω
C150-1 (HA1A) or C130-2 (HA1A) - Body ground Always 10 kΩ or higher
C150-3 (A1A+) or C130-22 (A1A+) - Body ground Always 10 kΩ or higher
C150-4 (A1A-) or C130-30 (A1A-) - Body ground Always 10 kΩ or higher
C148-1 (HA2A) or C130-1 (HA2A) - Body ground Always 10 kΩ or higher
C148-3 (A2A+) or C130-23 (A2A+) - Body ground Always 10 kΩ or higher
C148-4 (A2A-) or C130-31 (A2A-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

Result:
Result Proceed to
DTC is not output A
P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output B




A

END

B