Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

·

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E53
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.813 3.323,5.042 3.323,5.042 3.854,5.042 false 4.479,0.854 6.146,1.021 1.667,0.167 10 false Camshaft Position Sensor 4.479,1.354 6.208,1.51 1.729,0.156 10 false Crankshaft Position Sensor 0.115,0.052 1.667,0.302 1.552,0.25 10 false VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 false Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 false Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 false Correction 2.823,3.208 3.229,3.385 0.406,0.177 10 false ECM 1.604,3.771 3.813,3.948 2.208,0.177 10 false Camshaft Timing Oil Control Valve 0.177,2.719 0.875,2.896 0.698,0.177 10 false Duty Cycle 4.479,1.865 5.802,2.021 1.323,0.156 10 false Mass Air Flow Meter 4.479,2.885 6.823,3.073 2.344,0.188 10 false Engine Coolant Temperature Sensor 4.479,2.385 6.031,2.552 1.552,0.167 10 false Throttle Position Sensor 4.479,3.396 5.938,3.552 1.458,0.156 10 false Vehicle Speed Sensor 0.313,4.271 1.677,4.479 1.365,0.208 10 false Engine Oil Pressure 3.656,4.188 5.094,4.375 1.438,0.188 10 false Camshaft Timing Gear 3.896,4.979 5,5.24 1.104,0.26 10 false Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) Open or short in the camshaft timing oil control valve for intake camshaft (for Bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for intake camshaft (for Bank 1) circuit

·

Camshaft timing oil control valve assembly for intake camshaft (for Bank 1)

·

ECM


Comes on DTC stored

HINT:

This DTC relates to the camshaft timing oil control valve.


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

The monitor for this DTC runs 5 seconds after the ignition switch is turned to ON.

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

A133814
0.167,2.146 2.333,2.406 2.167,0.26 10 false Camshaft Timing Oil Control Valve 5.448,0.885 5.833,1.063 0.385,0.177 10 false OC1+ 5.448,1.792 5.802,1.969 0.354,0.177 10 false OC1- 5.948,2.531 6.333,2.688 0.385,0.156 10 false ECM 0.167,1.99 0.448,2.146 0.281,0.156 10 false C74 1.479,0.875 1.625,1.031 0.146,0.156 10 false 2 1.49,1.604 1.635,1.76 0.146,0.156 10 false 1 5.948,2.396 6.24,2.563 0.292,0.167 10 false C75 5.198,0.875 5.406,1.031 0.208,0.156 10 false 13 5.177,1.604 5.385,1.76 0.208,0.156 10 false 12

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs after recording the freeze frame data and DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

b.

Turn the ignition switch off.


c.

Start the engine and allow it to idle. Then check for DTCs.

Powertrain > Engine > Trouble Codes
50001 61

d.

Check that P0010 is not output.

OK:

P0010 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
a.

Disconnect the camshaft timing oil control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C74-2 - C75-13 (OC1+) Always Below 1 Ω
C74-1 - C75-12 (OC1-) Always Below 1 Ω
C74-2 or C75-13 (OC1+) - Body ground Always 10 kΩ or higher
C74-1 or C75-12 (OC1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR