Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A301836
1.792,2.198 2.208,1.781 false 0.104,0.135 0.594,0.365 0.49,0.229 10 false Fig. 1 0.094,0.396 0.958,0.677 0.865,0.281 10 false Resistance 0.052,0.719 0.49,0.958 0.438,0.24 10 false (kΩ) 0.573,0.813 1.01,1.052 0.438,0.24 8 false 30 0.573,1 1.01,1.24 0.438,0.24 8 false 20 0.563,1.313 1,1.552 0.438,0.24 8 false 10 0.625,1.646 1.063,1.885 0.438,0.24 8 false 5 0.625,1.885 1.063,2.125 0.438,0.24 8 false 3 0.625,2.073 1.063,2.313 0.438,0.24 8 false 2 0.635,2.385 1.073,2.625 0.438,0.24 8 false 1 0.531,2.646 0.969,2.885 0.438,0.24 8 false 0.5 0.531,2.833 0.969,3.073 0.438,0.24 8 false 0.3 0.521,3.146 0.958,3.385 0.438,0.24 8 false 0.2 0.531,3.469 0.969,3.708 0.438,0.24 8 false 0.1 0.802,3.854 1.125,4.198 0.323,0.344 8 false -20 (-4) 1.229,3.854 1.323,4.042 0.094,0.188 8 false 0 1.198,4.01 1.51,4.208 0.313,0.198 8 false 32 1.542,3.854 1.708,4.031 0.167,0.177 8 false 20 1.542,4.01 1.708,4.188 0.167,0.177 8 false 68 1.885,3.854 2.094,4.031 0.208,0.177 8 false 40 1.865,4.01 2.156,4.208 0.292,0.198 8 false 104 2.219,3.854 2.427,4.031 0.208,0.177 8 false 60 2.188,4.01 2.396,4.188 0.208,0.177 8 false 140 2.583,3.854 2.792,4.031 0.208,0.177 8 false 80 2.552,4.01 2.76,4.188 0.208,0.177 8 false 176 2.854,3.865 3.063,4.042 0.208,0.177 8 false 100 2.865,4.021 3.073,4.198 0.208,0.177 8 false 212 1.594,4.281 2.458,4.563 0.865,0.281 10 false Temperature 3.115,4.177 3.396,4.427 0.281,0.25 10 false (°C) 3.115,4.385 3.396,4.635 0.281,0.25 10 false (°F) 1.969,1.583 2.833,1.865 0.865,0.281 10 false Acceptable

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. The ECM continues operating in fail-safe mode until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Circuit Low Input Short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored
P0113 Intake Air Temperature Circuit High Input Open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


Comes on DTC stored

HINT:

When either of these DTCs is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit and stores DTC P0113. Conversely, if the output voltage is below 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit and stores DTC P0112.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

A247765
0.792,1.885 1.292,2.135 0.5,0.25 10 false C36 0.792,2.042 2.354,2.406 1.563,0.365 10 false Mass Air Flow Meter 2.073,0.615 2.51,0.865 0.438,0.25 10 false THA 2.167,1.229 2.479,1.417 0.313,0.188 10 false E2 2.427,0.604 2.552,0.771 0.125,0.167 10 false 4 2.427,1.229 2.552,1.396 0.125,0.167 10 false 5 5.177,1.333 5.594,1.573 0.417,0.24 10 false C75 5.177,0.719 5.594,0.948 0.417,0.229 10 false C76 5.219,1.146 5.51,1.396 0.292,0.25 10 false 28 5.229,0.521 5.542,0.74 0.313,0.219 10 false 29 5.521,0.604 5.979,0.813 0.458,0.208 10 false THA 5.521,1.229 5.865,1.51 0.344,0.281 10 false E2 5.99,2.26 6.531,2.542 0.542,0.281 10 false ECM 6.25,0.24 6.573,0.583 0.323,0.344 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

e.

Read the value displayed on the intelligent tester.

OK:

Same as actual intake air temperature


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A303214
1.542,0.688 1.938,0.938 0.396,0.25 0.385,3.385 0.781,3.635 0.396,0.25 1.615,4.042 1.896,3.656 true 2.219,4.021 2.146,3.656 true 0.76,1.792 1.073,1.99 0.313,0.198 10 false *1 2.573,1.792 2.885,1.99 0.313,0.198 10 false *2 2.458,1.052 2.771,1.25 0.313,0.198 10 false THA 2.479,1.51 2.792,1.708 0.313,0.198 10 false E2 0.24,2.51 0.552,2.708 0.313,0.198 10 false *a 1.604,0.729 2.063,0.927 0.458,0.198 10 false C36 1.458,4.052 1.917,4.25 0.458,0.198 10 false THA 2.135,4.052 2.594,4.25 0.458,0.198 10 false E2 1.75,1.042 2.063,1.24 0.313,0.198 10 false 4 1.76,1.427 2.073,1.625 0.313,0.198 10 false 5 0.469,3.427 0.927,3.625 0.458,0.198 10 false C36
*1 Mass Air Flow Meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

g.

Read the value displayed on the intelligent tester.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-4 (THA) - C76-29 (THA) Always Below 1 Ω
C36-5 (E2) - C75-28 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A186168
1.406,0.698 1.75,0.906 0.344,0.208 0.76,1.74 1.073,1.896 0.313,0.156 10 false *1 2.656,1.75 2.969,1.906 0.313,0.156 10 false *2 1.458,0.719 1.885,0.927 0.427,0.208 10 false C36 2.438,1.042 2.865,1.25 0.427,0.208 10 false THA 2.448,1.51 2.875,1.719 0.427,0.208 10 false E2
*1 Mass Air Flow Meter
*2 ECM


Disconnect the mass air flow meter connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

f.

Read the value displayed on the intelligent tester.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-4 (THA) or C76-29 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR