Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P1613  Secondary Air Injection Driver Malfunction  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1613 Secondary Air Injection Driver Malfunction Condition 1:
Either condition (1) or (2) met:
(1) All conditions are met (1 trip detection logic):
·

Either the air pump or the air switching valve is not operating.

·

Diagnostic signal from the air injection control driver is 80%.

·

Battery voltage is 8 V or higher.


(2) Both conditions are met (1 trip detection logic):
·

Battery voltage is 8 V or higher.

·

Diagnostic signal from the air injection control driver is abnormal (duty signal other than 0, 20, 40, 80 or 100%).


Condition 2:

All conditions are met (1 trip detection logic):

1.

Secondary air injection system operating (air switching valve and air pump are on).

2.

Diagnostic signal from the air injection control driver is 0%.

3.

Battery voltage is 8 V or higher.



Condition 3:

Both conditions are met (1 trip detection logic):

1.

Battery voltage is 8 V or higher.

2.

Diagnostic signal from the air injection control driver is 100%.



Condition 1:
·

Air injection control driver

·

Open in air injection control driver ground circuit


Condition 2:
·

Open in air pump or air switching valve command signal circuit (ECM - air injection control driver)

·

Open in air injection control driver ground circuit

·

Short between diagnostic signal circuit and body ground

·

Air injection control driver

·

ECM


Condition 3:
·

Open in diagnostic signal circuit

·

Air injection control driver

·

Open in air injection control driver +B circuit (air injection control driver power source)

·

Short between +B and diagnostic signal circuits

·

Short in air pump or air switching valve command signal circuit (ECM - air injection control driver)

·

Open in air injection control driver ground circuit


Comes on DTC stored

MONITOR DESCRIPTION

For a short time a after cold engine start, the ECM transmits command signals to the air injection control driver to drive the air pump and air switching valve. The air injection control driver detects open and short circuits according to the voltages at the air injection control driver terminals connected to the air pump and air switching valve, and the circuit voltage of the air injection control driver power source, and transmits diagnostic information as a signal to the ECM.

If the Secondary Air Injection (AIR) system circuit or the air injection control driver itself malfunctions, the air injection control driver sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM stores the DTC based on the diagnostic information from the air injection control driver.

Example:

1.

The duty ratio of the diagnostic signal from the air injection control driver is 0 or 100% (remains at 0 V or is the same as battery voltage).

2.

The duty ratio of the diagnostic signal from the air injection control driver shows an impossible ratio (other than 0, 20, 40, 80 or 100%).

3.

The air injection control driver outputs the normal signal (normal duty signal: 80%) while the system is not operating.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Diagnostic information output by the air injection control driver can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the air injection control driver. Reading the waveform while performing the AIR system forced operation provided in the system check allows the possible trouble areas to be narrowed down.


(a) Start the engine and warm it up.

(b) Turn the ignition switch off.

(c) Connect the intelligent tester to the DLC3.

A262769
2.833,0.167 3.24,0.406 0.406,0.24 0.604,0.167 1.188,0.427 0.583,0.26 0.677,1.021 0.917,1.573 true 2.865,0.719 2.938,1.51 true 0.083,0.01 0.25,0.177 0.167,0.167 10 false *a 0.729,0.219 1.094,0.385 0.365,0.167 10 false G146 2.927,0.208 3.208,0.365 0.281,0.156 10 false C98 0.958,1.5 1.542,1.677 0.583,0.177 10 false 30 (AIDI) 2.917,1.521 3.333,1.677 0.417,0.156 10 false 5 (E1)
*a Component with harness connected
(ECM)


(d) Connect oscilloscope probes to the AIDI and E1 terminals of the ECM.

(e) Turn the ignition switch to ON and turn the intelligent tester on.

(f) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.

HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


(g) Start the engine.

(h) Perform the AIR system forced operation while the engine is idling.

G037721
2.938,1.292 3.333,1.49 0.396,0.198 10 false GND 2.677,0.073 3.281,0.271 0.604,0.198 10 false 5 V/DIV. 1.563,1.865 2.344,2.063 0.781,0.198 10 false 20 ms/DIV. 0.5,0.448 2.24,0.656 1.74,0.208 10 true Example: 80% Duty Signal

(i) Monitor the air injection control driver voltage output (duty ratio signal).

Measurement Condition
Item Content
ECM Terminal Name AIDI - E1
Tester Range 5 V/DIV., 20 ms/DIV.
Condition Idling

(j) Turn the ignition switch off.

NOTICE:
·

Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While AIR system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (Wait or Error).

If Error is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the AIR system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




HINT:
·

By using the intelligent tester to perform the Secondary Air Injection Check operation in the system check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read DTCs.

Result:
Result Proceed to

If any DTCs other than P1613 are output, troubleshoot those DTCs first.

P1613 A
P1613 and other DTCs B




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIDI VOLTAGE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIDI VOLTAGE)
a.
A262769
0.615,0.188 1.031,0.417 0.417,0.229 2.75,0.188 3.167,0.417 0.417,0.229 2.927,1.521 2.844,0.74 true 0.938,1.635 0.677,1.021 true 0.083,0.052 0.365,0.313 0.281,0.26 10 false *a 0.667,0.229 1.063,0.448 0.396,0.219 10 false G146 2.844,0.219 3.146,0.448 0.302,0.229 10 false C98 0.99,1.573 1.635,1.833 0.646,0.26 10 false 30 (AIDI) 2.896,1.542 3.365,1.833 0.469,0.292 10 false 5 (E1)
*a Component with harness connected
(ECM)


Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.

HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

f.

Start the engine.


g.

Perform the AIR system forced operation while the engine is idling.


h.

Measure the voltage between the AIDI and E1 terminals of the ECM connector when the AIR system is on and off.


i.

Turn the ignition switch off.

NOTICE:
·

Do not perform the system check operation repetitively. It may cause the damage in the system. If it is necessary to repeat the check, leave an interval of several minutes between system check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Result:
Results Suspected Trouble Areas Proceed To
Fixed at low voltage (1.6 V or less) even when AIR system ON (Air pump ON, ASV OPEN)
·

Short between air pump or air switching valve command signal circuit and body ground

·

Open in air pump command signal circuit (between ECM and air injection control driver)

·

Open in air switching valve assembly command signal circuit (between ECM and air injection control driver)

·

Open in air injection control driver ground circuit (between air injection control driver and body ground)

·

Diagnostic signal circuit ground short

·

Air injection control driver

·

ECM


A
Fixed at high voltage (12 V or higher) even when AIR system OFF (Air pump OFF, ASV CLOSE)
·

Open in diagnostic signal circuit (ECM - air injection control driver)

·

Short between +B and diagnostic signal circuits (ECM - air injection control driver)

·

Open in air injection control driver power source circuit

·

Air injection control driver

·

ECM


B
Other than above:
Fluctuating (duty signal other than 20, 40 or 80%)
·

Air injection control driver

·

Open in air injection control driver ground circuit (between air injection control driver and body ground)


C




A

3.INSPECT ECM (AIRP AND AIRV VOLTAGE)

B

4.CHECK AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

C

8.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - BODY GROUND)
3.INSPECT ECM (AIRP AND AIRV VOLTAGE)
a.
A262769
0.438,0.188 0.854,0.417 0.417,0.229 2.75,0.188 3.167,0.417 0.417,0.229 2.823,1.542 2.844,0.74 true 0.438,1.531 0.521,1.01 true 0.938,1.552 0.573,0.802 true 0.083,0.052 0.365,0.313 0.281,0.26 10 false *a 0.479,0.229 0.875,0.448 0.396,0.219 10 false G145 2.844,0.219 3.146,0.448 0.302,0.229 10 false C98 0.167,1.573 0.813,1.833 0.646,0.26 10 false 19 (AIRP) 2.792,1.542 3.26,1.833 0.469,0.292 10 false 5 (E1) 0.917,1.573 1.563,1.833 0.646,0.26 10 false 6 (AIRV)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G145-19 (AIRP) - C98-5 (E1) Ignition switch ON 11 to 14 V
G145-6 (AIRV) - C98-5 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
4.CHECK AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
a.
B053781
0.177,0.885 0.531,1.125 0.354,0.24 0.635,1.698 1.052,1.281 true 1.115,1.76 1.323,1.302 true 0.063,0.063 0.427,0.354 0.365,0.292 10 false *a 0.24,0.927 0.604,1.219 0.365,0.292 10 false C86 0.531,1.708 0.896,2 0.365,0.292 10 false E 1.052,1.792 1.417,2.083 0.365,0.292 10 false DI
*a Front view of wire harness connector
(to Air Injection Control Driver)


Disconnect the air injection control driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C86-5 (+B) - Body ground Ignition Switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G145-19 (AIRP) or C86-4 (SIP) - Body ground Always 10 kΩ or higher
G145-6 (AIRV) or C86-3 (SIV) - Body ground Always 10 kΩ or higher



e.

Reconnect the air injection control driver connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
a.
B053781
0.177,0.885 0.531,1.125 0.354,0.24 0.635,1.698 1.052,1.281 true 1.115,1.76 1.323,1.302 true 0.063,0.063 0.427,0.354 0.365,0.292 10 false *a 0.24,0.927 0.604,1.219 0.365,0.292 10 false C86 0.531,1.708 0.896,2 0.365,0.292 10 false E 1.052,1.792 1.417,2.083 0.365,0.292 10 false DI
*a Front view of wire harness connector
(to Air Injection Control Driver)


Disconnect the air injection control driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C86-2 (DI) - C86-1 (E) Ignition Switch ON 11 to 14 V



d.

Reconnect the air injection control driver connector.


Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
6.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C86-1 (E) - Body ground Always Below 1 Ω
C86-4 (SIP) - G145-19 (AIRP) Always Below 1 Ω
C86-3 (SIV) - G145-6 (AIRV) Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (Check for Short):
Tester Connection Condition Specified Condition
C86-2 (DI) - C86-1 (E) Ignition switch ON 11 to 14 V



Result:
Result Proceed to
NG A
OK B


e.

Reconnect the ECM connector.


f.

Reconnect the air injection control driver connector.



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C86-2 (DI) - G146-30 (AIDI) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C86-2 (DI) or G146-30 (AIDI) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM and air injection control driver connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - BODY GROUND)
a.

Disconnect the air injection control driver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C86-1 (E) - Body ground Always Below 1 Ω



c.

Reconnect the air injection control driver connector.


Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Disconnect the air injection control driver connector.


b.
A229922
0.646,2.479 1.01,2.698 0.365,0.219 1.146,3.031 1.365,2.604 true 1.5,3.031 1.531,2.625 true 1.865,3.021 1.667,2.625 true 2.271,3.021 1.813,2.625 true 0.646,0.323 0.958,0.479 0.313,0.156 10 false *1 2.552,0.156 2.865,0.313 0.313,0.156 10 false *2 0.99,2 1.302,2.24 0.313,0.24 10 false *a 0.813,0.781 1.135,1.01 0.323,0.229 10 false DI 0.75,1.135 1.073,1.365 0.323,0.229 10 false SIV 2.417,0.771 2.74,1 0.323,0.229 10 false AIDI 2.417,1.135 2.917,1.406 0.5,0.271 10 false AIRV 0.698,2.51 1.021,2.74 0.323,0.229 10 false C86 1.104,3.042 1.427,3.271 0.323,0.229 10 false E 1.448,3.042 1.771,3.271 0.323,0.229 10 false DI 1.792,3.042 2.115,3.271 0.323,0.229 10 false SIV 2.198,3.042 2.521,3.271 0.323,0.229 10 false SIP
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


Connect terminals DI and SIV of the wire harness connector for the air injection control driver.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

f.

Start the engine.


g.

Perform the AIR system intrusive operation while the engine is idling.


h.

Measure the voltage between the SIV and E terminals of the ECM connector when the AIR system is on and off.


i.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
C86-3 (SIV) - C86-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C86-3 (SIV) - C86-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



j.
A229922
0.646,2.479 1.01,2.698 0.365,0.219 1.146,3.031 1.365,2.604 true 1.5,3.031 1.531,2.625 true 1.865,3.021 1.667,2.625 true 2.271,3.021 1.813,2.625 true 0.646,0.323 0.958,0.479 0.313,0.156 10 false *1 2.552,0.156 2.865,0.313 0.313,0.156 10 false *2 0.99,2 1.302,2.24 0.313,0.24 10 false *a 0.813,0.781 1.135,1.01 0.323,0.229 10 false DI 0.75,1.135 1.073,1.365 0.323,0.229 10 false SIV 2.417,0.771 2.74,1 0.323,0.229 10 false AIDI 2.417,1.135 2.917,1.406 0.5,0.271 10 false AIRV 0.698,2.51 1.021,2.74 0.323,0.229 10 false C86 1.104,3.042 1.427,3.271 0.323,0.229 10 false E 1.448,3.042 1.771,3.271 0.323,0.229 10 false DI 1.792,3.042 2.115,3.271 0.323,0.229 10 false SIV 2.198,3.042 2.521,3.271 0.323,0.229 10 false SIP
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


Connect terminals DI and SIP of the wire harness connector for the air injection control driver.


k.

Connect the intelligent tester to the DLC3.


l.

Turn the ignition switch to ON and turn the intelligent tester on.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

n.

Start the engine.


o.

Perform the AIR system intrusive operation while the engine is idling.


p.

Measure the voltage between the SIP and E terminals of the ECM connector when the AIR system is on and off.


q.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
C86-4 (SIP) - C86-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
C86-4 (SIP) - C86-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



r.

Reconnect the air injection control driver connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE AIR INJECTION CONTROL DRIVER

NG

10.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE)
11.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the intelligent tester on.


e.

Clear DTCs (if stored).

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

g.

Start the engine after the intelligent tester initialization is finished.


h.

Perform the system check operation by pressing Next.


i.

After operating the AIR system, press the Exit button to confirm the AIR system pending codes.


j.

Check Pending DTCs.

OK:

No pending DTC output.



k.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Proceed to
OK
NG



OK

END

NG