Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0657  Actuator Supply Voltage Circuit / Open  


DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the ignition switch is turned off. If the output voltage is higher than 7 V when the ignition switch is turned off, the ECM will illuminate the MIL and store a DTC when the ignition switch is turned to ON.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0657 Actuator Supply Voltage Circuit / Open There is a throttle actuator power supply error (1 trip detection logic). ECM Comes on DTC stored

MONITOR STRATEGY

Required sensors/Components ECM
Frequency of operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Throttle actuator power supply voltage 7 V or higher

TYPICAL MALFUNCTION THRESHOLDS

Ignition switch From ON to off (Temporary Fail ON)
Throttle actuator power supply ON

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the intelligent tester off.

5.

Turn the ignition switch off.

6.

Disconnect the intelligent tester.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Connect the intelligent tester to the DLC3.

10.

Turn the ignition switch to ON.

11.

Wait 10 seconds or more.

12.

Turn the ignition switch off and wait 15 seconds or more.

13.

Turn the ignition switch to ON and turn the intelligent tester on.

14.

Wait 5 seconds or more.

15.

Enter the following menus: Powertrain / Engine and ECT / DTC.

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P0657.

19.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




PROCEDURE

1.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the intelligent tester off.


f.

Turn the ignition switch off.


g.

Disconnect the intelligent tester.


h.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


i.

Connect the cable to the negative (-) battery terminal.


j.

Turn the ignition switch to ON.


k.

Wait 10 seconds or more.


l.

Turn the ignition switch off.


m.

Wait 15 seconds or more.


n.

Connect the intelligent tester to the DLC3.


o.

Turn the ignition switch to ON and turn the intelligent tester on.


p.

Wait 5 seconds or more.


q.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

r.

Check for DTCs.

OK:

P0657 is not output.



Result:
Proceed to
OK
NG



OK

NG