Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal rod assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in depending on the position of the accelerator pedal (throttle valve). The signal from VPA indicates the actual accelerator pedal position (throttle valve opening angle) and is used for engine control. The signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal position (throttle valve opening angle) through the signals from VPA and VPA2 and controls the throttle actuator according to these signals.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


A255989
4.344,2.917 4.219,2.917 false 4.344,2.417 4.219,2.417 false 4.344,2.208 4.219,2.208 false 4.354,3.125 4.208,3.125 false 0.844,2.875 0.552,3.292 true 0.969,3.208 1.052,3.531 true 0.927,2.531 0.865,1.969 true 1.063,2.208 1.26,1.75 true 4.333,1.844 3.844,0.948 false 0.094,3.792 2.385,4.042 2.292,0.25 10 false Accelerator Pedal Position Sensor 1.302,1.698 1.865,1.927 0.563,0.229 10 false Magnet 0.344,1.875 0.969,2.094 0.625,0.219 10 false IC No. 1 0.313,3.344 0.917,3.563 0.604,0.219 10 false IC No. 2 2.063,1.74 2.458,1.969 0.396,0.229 10 false VPA 2.063,2.073 2.458,2.313 0.396,0.24 10 false EPA 2.063,2.396 2.542,2.625 0.479,0.229 10 false VCPA 2.063,2.698 2.521,2.896 0.458,0.198 10 false VPA2 2.063,3 2.51,3.219 0.448,0.219 10 false EPA2 2.063,3.323 2.51,3.531 0.448,0.208 10 false VCP2 2.698,3.729 3.125,4.021 0.427,0.292 10 false ECM 4.271,1.552 4.594,1.75 0.323,0.198 10 false *1 5.865,1.552 6.146,1.781 0.281,0.229 10 false *2 3.844,2.135 4.302,2.396 0.458,0.26 10 false 3.988 3.844,2.344 4.271,2.531 0.427,0.188 10 false 3.188 3.99,2.833 4.333,3.094 0.344,0.26 10 false 1.6 3.99,3.042 4.313,3.292 0.323,0.25 10 false 0.8 4.406,3.344 4.781,3.573 0.375,0.229 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.146,3.792 0.365,0.198 10 false 15.9 4.688,3.583 5.708,3.844 1.021,0.26 10 false Usable Range 4.365,4.052 6.656,4.333 2.292,0.281 10 false Accelerator Pedal Turning Angle (°) 0.24,5.177 2.646,5.417 2.406,0.24 10 false *1: Accelerator Pedal Fully Released 0.229,5.49 2.667,5.708 2.438,0.219 10 false *2: Accelerator Pedal Fully Depressed 0.865,3.531 1.396,3.76 0.531,0.229 10 false Magnet 2.135,0.854 3.771,1.385 1.635,0.531 10 false Accelerator Pedal Position Sensor Output Voltage (V)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input VPA is 0.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal position sensor

·

Open in VCP1 circuit

·

Open or short to ground in VPA circuit

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal position sensor

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input VPA2 is 0.5 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
·

Accelerator pedal position sensor

·

Open in VCP2 circuit

·

Open or short to ground in VPA2 circuit

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.2 V and 3.45 V.
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.2 V or less and VPA2 is 0.5 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal position sensor

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs is stored, check the accelerator pedal position sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Area Accel Sensor Out No. 1
When Accelerator Pedal Released
Accel Sensor Out No. 2
When Accelerator Pedal Released
Accel Sensor Out No. 1
When Accelerator Pedal Depressed
Accel Sensor Out No. 2
When Accelerator Pedal Depressed
VCP circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or short to ground in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or short to ground in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA circuit open 4.5 to 5.5 V 4.5 to 5.5 V 4.5 to 5.5 V 4.5 to 5.5 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA drops below 0.2 V for more than 0.5 seconds when the accelerator pedal is fully depressed, DTC P2122 is stored.

If the malfunction is not repaired successfully, a DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal position sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

VPA voltage 0.4 to 4.8 V
VPA2 voltage 1.2 to 4.8 V
Difference between VPA and VPA2 voltages More than 0.02 V

CONFIRMATION DRIVING PATTERN

A199317
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.438 5.115,1.792 5.115,1.792 5.26,1.792 false 2.208,2.438 2.438,2.094 2.438,2.094 2.542,2.094 false 0.125,0.094 1.771,0.354 1.646,0.26 10 false Accelerator Pedal State 0.875,0.417 1.74,0.667 0.865,0.25 10 false Depressed 0.948,0.875 1.646,1.104 0.698,0.229 10 false Released 0.406,2.385 1.729,2.677 1.323,0.292 10 false Ignition Switch ON 2.094,2.49 2.396,2.771 0.302,0.281 10 false [A] 4.396,3.438 4.667,3.677 0.271,0.24 10 false [C] 5.323,1.688 6.063,1.927 0.74,0.24 10 false Released 2.875,3.042 3.75,3.323 0.875,0.281 10 false 5 seconds 3,1.208 3.771,1.448 0.771,0.24 10 false Depressed 3.885,1.125 4.198,1.375 0.313,0.25 10 false [B] 2.594,2.031 3.375,2.313 0.781,0.281 10 false Released

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Fully depress and release the accelerator pedal [B].

7.

Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.

12.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.




FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A229976
6.014,3.251 6.355,3.407 0.341,0.156 10 ECM 5.584,0.462 5.898,0.627 0.314,0.166 10 VPA 5.584,1.097 5.898,1.262 0.314,0.166 10 EPA 5.594,1.326 6.0,1.491 0.406,0.166 10 VCPA 5.594,1.723 5.991,1.888 0.397,0.166 10 VPA2 5.594,2.358 5.991,2.523 0.397,0.166 10 EPA2 5.594,2.587 6.0,2.752 0.406,0.166 10 VCP2 1.607,0.564 1.92,0.73 0.312,0.166 10 VPA 1.607,0.987 1.921,1.153 0.314,0.166 10 EPA 1.5,1.4 1.906,1.566 0.406,0.166 10 VCPA 1.51,1.821 1.907,1.986 0.397,0.166 10 VPA2 1.51,2.242 1.898,2.408 0.388,0.166 10 EPA2 1.5,2.668 1.906,2.834 0.406,0.166 10 VCP2 5.361,0.481 5.564,0.646 0.203,0.166 10 18 5.361,0.906 5.564,1.071 0.203,0.166 10 20 5.361,1.323 5.564,1.488 0.203,0.166 10 26 5.361,1.736 5.564,1.901 0.203,0.166 10 19 5.361,2.161 5.564,2.326 0.203,0.166 10 21 5.361,2.586 5.564,2.751 0.203,0.166 10 27 1.988,0.485 2.103,0.651 0.115,0.166 10 6 1.988,0.905 2.103,1.071 0.115,0.166 10 5 1.988,1.326 2.103,1.491 0.115,0.166 10 4 1.988,1.746 2.103,1.911 0.115,0.165 10 3 1.988,2.166 2.103,2.332 0.115,0.166 10 2 1.988,2.587 2.103,2.752 0.115,0.166 10 1 0.2,3.083 0.506,3.248 0.307,0.166 10 G6 0.2,3.24 2.383,3.406 2.183,0.166 10 Accelerator Pedal Position Sensor 6.014,3.09 6.312,3.256 0.298,0.166 10 G89

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the accelerator pedal position sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION SENSOR)
a.
A208621
0.74,1.76 1.052,1.917 0.313,0.156 10 false *a 2.625,1.771 2.938,1.927 0.313,0.156 10 false *b
*a Depressed
*b Released


Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Powertrain > Engine > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 61 128,129

e.

Read the value displayed on the intelligent tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2 Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V More than 0.02 V
Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-6 (VPA) - G89-18 (VPA) Always Below 1 Ω
G6-5 (EPA) - G89-20 (EPA) Always Below 1 Ω
G6-4 (VCPA) - G89-26 (VCPA) Always Below 1 Ω
G6-3 (VPA2) - G89-19 (VPA2) Always Below 1 Ω
G6-2 (EPA2) - G89-21 (EPA2) Always Below 1 Ω
G6-1 (VCP2) - G89-27 (VCP2) Always Below 1 Ω
G6-6 (VPA) or G89-18 (VPA) - Body ground Always 10 kΩ or higher
G6-5 (EPA) or G89-20 (EPA) - Body ground Always 10 kΩ or higher
G6-4 (VCPA) or G89-26 (VCPA) - Body ground Always 10 kΩ or higher
G6-3 (VPA2) or G89-19 (VPA2) - Body ground Always 10 kΩ or higher
G6-2 (EPA2) or G89-21 (EPA2) - Body ground Always 10 kΩ or higher
G6-1 (VCP2) or G89-27 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
a.
A200902
0.583,0.969 0.917,1.198 0.333,0.229 0.823,1.448 1.375,1.115 false 1.344,1.583 1.521,1.115 false 1.948,1.604 1.781,1.115 false 2.333,1.479 1.948,1.115 false 0.115,0.052 0.51,0.302 0.396,0.25 10 false *a 0.667,1 1.063,1.25 0.396,0.25 10 false G6 0.74,1.458 1.24,1.688 0.5,0.229 10 false VCP2 1.229,1.615 1.729,1.844 0.5,0.229 10 false EPA2 1.823,1.615 2.323,1.844 0.5,0.229 10 false VCPA 2.354,1.458 2.854,1.688 0.5,0.229 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-4 (VCPA) - G6-5 (EPA) Ignition switch ON 4.5 to 5.5 V
G6-1 (VCP2) - G6-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 is output A
No DTC is output B




A

B

END