Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P1229  Fuel Pump System  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1229 Fuel Pump System The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or higher for 30 seconds.
(1 trip detection logic)
·

Short in fuel supply pump assembly (suction control valve) circuit

·

Fuel supply pump assembly (suction control valve)

·

Fuel pressure sensor (common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1229
·

Fuel Press

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>SYSTEM DESCRIPTION).

·

When DTC P1229 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure.

Under a stable condition such as idling after warm up the engine, Fuel Press is within +/-5000 kPa of Target Common Rail Pressure when normal.

·

When there is a problem with the movement of the fuel supply pump assembly (when Fuel Press is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.



CONFIRMATION DRIVING PATTERN

P1229
DTC Detection Drive Pattern Idling for 60 seconds

MONITOR DESCRIPTION

P1229 (Fuel overfeed):

The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Fuel Press", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P1229 and "P0190, P0192 and/or P0193" are output B
Except above A




A

2.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine > Data List
Tester Display
Target Common Rail Pressure
Fuel Press
50003 61 416,54

e.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Fuel Press is within 5000 kPa of Target Common Rail Pressure when engine is idling after warm up the engine.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-1 - C22-2 (PCV+) Always Below 1 Ω
C5-2 - C22-1 (PCV-) Always Below 1 Ω
C5-1 or C22-2 (PCV+) - Body ground Always 10 kΩ or higher
C5-2 or C22-1 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

6.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 416,54

d.
A241174
2.042,2.75 2.427,2.271 2.427,2.271 2.646,2.271 true 2.677,2.167 2.917,2.385 0.24,0.219 10 false *1
*1 Snapshot Button


Take a snapshot with the intelligent tester during the Active Test.

HINT:

Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.



e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.49,2.583 5.01,2.479 5.01,2.479 5.073,2.479 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.281 3.938,4.198 3.938,4.198 4.073,4.198 false 0.083,1.448 1.448,1.604 1.365,0.156 10 false Active Test Operation 0.167,0.615 1.563,0.813 1.396,0.198 10 false Engine Speed (rpm) 0.542,3.323 1.448,3.563 0.906,0.24 10 false Fuel Pressure 3.646,2.01 5,2.177 1.354,0.167 10 false Target Fuel Pressure 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.438 2.865,2.802 0.74,0.365 10 false Less than 10000 kPa 2.969,4.292 3.656,4.458 0.688,0.167 10 false 2 seconds 5.146,2.385 6.063,2.76 0.917,0.375 10 false Abnormal Fuel Pressure 2.448,1.146 3.125,1.344 0.677,0.198 10 false Test Start 4.208,1.135 4.885,1.479 0.677,0.344 10 false Test Stop 5.625,1.146 6.302,1.344 0.677,0.198 10 false Test Start 2.208,1.823 2.969,2.24 0.76,0.417 10 false Normal Fuel Pressure 1.646,0.313 2.021,0.479 0.375,0.167 10 false 2000 1.885,0.865 2.052,1.031 0.167,0.167 10 false 0 1.75,1.333 2.073,1.5 0.323,0.167 10 false ON 1.698,1.594 2.021,1.76 0.323,0.167 10 false OFF 4.146,4.135 5.802,4.469 1.656,0.333 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. B
Except above A




A

6.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

B

10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

9.PERFORM FUEL SUPPLY PUMP INITIALIZATION
9.PERFORM FUEL SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1229.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END