Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0168  Fuel Temperature Too High  


DESCRIPTION

Refer to DTC P0180 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0180).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0168 Fuel Temperature Too High All of following conditions are met (1 trip detection logic):
·

The engine speed is more than 5000 rpm.

·

The vehicle speed is more than 10 km/h (6.25 mph).

·

The fuel temperature is 96°C (205°F) or higher for the specified time.


·

Fuel cooler (Problem cooling fuel)

·

Fuel lines or fuel filter clogged


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0168
DTC Detection Drive Pattern Drive vehicle at high speed or with heavy load (Use freeze frame data from time malfunction occurred as reference while driving)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0168)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0168 is output A
P0168 and other DTCs are output B


HINT:

If DTCs other than P0168 are output, perform troubleshooting for those codes first.




A

2.CHECK FUEL SUPPLY PUMP ASSEMBLY

B

2.CHECK FUEL SUPPLY PUMP ASSEMBLY
a.

Perform a visual inspection of the exterior of the fuel supply pump assembly and check that there are no fuel leaks.

OK:

There are no fuel leaks or stains.



Result:
Proceed to
OK
NG



OK

3.CHECK FUEL SYSTEM

NG

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY
3.CHECK FUEL SYSTEM
a.

Check if dirt is clogging the fuel cooler cooling fins. Clean the fins if they are clogged with dirt.

HINT:

If the fuel cooler cooling fins are not clogged with dirt, replace the fuel filter.



Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY

Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
6.PERFORM FUEL SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON and turn the tester on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

f.

Drive the vehicle in a city area and check that the value of Fuel Temperature does not exceed 110°C (230°F).


Result:
Proceed to
NEXT



NEXT

END