Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2012.04–2012.10
RM1840EF _57 Power Source / Network _009639 NETWORKING _0052677 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "Bus Check" screen.

·

"Skid Control ECU Communication Stop Mode" in "DTC Communication Table" applies.


·

Power source or inside of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C240993
5.406,4.781 5.688,4.938 0.281,0.156 10 false A36 5.406,4.948 7.01,5.281 1.604,0.333 10 false Brake Actuator Assembly (Skid Control ECU) 5.76,1.083 6.167,1.26 0.406,0.177 10 false CANL 5.74,0.573 6.156,0.771 0.417,0.198 10 false CANH 5.5,0.5 5.677,0.688 0.177,0.188 10 false 25 5.49,1 5.667,1.167 0.177,0.167 10 false 14 5.729,3.656 6.146,3.823 0.417,0.167 10 false GND1 5.74,4.146 6.135,4.333 0.396,0.188 10 false GND2 5.781,3.156 6.188,3.323 0.406,0.167 10 false IG1 5.74,2.625 6.135,2.792 0.396,0.167 10 false +BS 5.75,2.104 6.156,2.271 0.406,0.167 10 false +BM 5.51,2.021 5.677,2.177 0.167,0.156 10 false 24 5.479,2.542 5.656,2.708 0.177,0.167 10 false 12 5.5,3.052 5.688,3.25 0.188,0.198 10 false 34 5.552,3.563 5.656,3.698 0.104,0.135 10 false 1 5.5,4.083 5.677,4.229 0.177,0.146 10 false 13 1.594,0.479 1.76,0.646 0.167,0.167 10 false 13 1.635,1 1.813,1.135 0.177,0.135 10 false 7 0.51,1.375 0.802,1.531 0.292,0.156 10 false G87 0.51,1.542 2.135,1.708 1.625,0.167 10 false No. 1 Junction Connector 1.708,2.094 2.563,2.313 0.854,0.219 10 false from Battery 1.698,2.615 2.479,2.844 0.781,0.229 10 false from Battery 1.26,3.125 2.5,3.271 1.24,0.146 10 false from Ignition Switch 3.76,3 4.854,3.177 1.094,0.177 10 false ECU-IG&GAUGE 3.708,2.5 4.563,2.667 0.854,0.167 10 false ABS NO.2 3.708,1.969 4.583,2.188 0.875,0.219 10 false ABS NO.1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Result:
Proceed to
NEXT



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C234968C39
0.125,1.01 0.677,1.344 0.552,0.333 1.875,1.958 1.792,1.958 1.792,1.958 1.479,1.281 true 1.448,1.365 1.188,1.938 1.188,1.938 1.083,1.938 true 0.281,1.094 0.563,1.271 0.281,0.177 10 false A36 1.917,1.885 2.323,2.031 0.406,0.146 10 false CANL 0.688,1.854 1.094,2 0.406,0.146 10 false CANH 0.073,0.052 0.333,0.198 0.26,0.146 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the A36 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A36-25 (CANH) - A36-14 (CANL) Ignition switch off 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C234968C40
0.125,1.01 0.677,1.344 0.552,0.333 1.917,1.969 2,1.969 2,1.969 2.229,1.365 true 2.479,1.042 2.177,0.333 2.177,0.333 2.271,0.333 true 2.521,1.323 2.354,1.948 2.354,1.948 2.458,1.948 true 1.208,1.052 0.917,0.469 0.917,0.469 0.813,0.469 true 1.219,1.344 0.896,1.917 0.896,1.917 0.802,1.917 true 0.271,1.104 0.552,1.271 0.281,0.167 10 false A36 1.667,1.885 1.927,2.031 0.26,0.146 10 false IG1 0.406,1.833 0.823,1.979 0.417,0.146 10 false GND2 0.427,0.396 0.875,0.542 0.448,0.146 10 false GND1 0.083,0.063 0.344,0.208 0.26,0.146 10 false *a 2.479,1.875 2.792,2.021 0.313,0.146 10 false +BM 2.313,0.26 2.604,0.406 0.292,0.146 10 false +BS
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-12 (+BS) - Body ground Always 11 to 14 V
A36-24 (+BM) - Body ground Always 11 to 14 V
A36-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-1 (GND1) - Body ground Always Below 1 Ω
A36-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR