This DTC is stored when a malfunction occurs in the navigation antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | Short in GPS Antenna | A GPS antenna error. | ·
Navigation antenna assembly (w/o Blocking System) ·
Navigation antenna cord sub-assembly (w/o Blocking System) ·
Instrument panel integration antenna assembly (w/ Blocking System) ·
Divider antenna assembly (w/ Blocking System) ·
Navigation receiver assembly |
| B15C1 | Open in GPS Antenna | An error of the power source to the GPS antenna. | ·
Navigation antenna assembly (w/o Blocking System) ·
Navigation antenna cord sub-assembly (w/o Blocking System) ·
Instrument panel integration antenna assembly (w/ Blocking System) ·
Divider antenna assembly (w/ Blocking System) ·
Navigation receiver assembly |
w/o Blocking System
w/ Blocking System
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs and check if the same trouble occurs again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
*1: w/o Blocking System
*2: w/ Blocking System
Check if the navigation antenna assembly*1 or instrument panel integration antenna assembly*2 is securely connected to the navigation receiver assembly.
Navigation antenna assembly*1 or instrument panel integration antenna assembly*2 is securely connected.
| Result | Proceed to |
|---|---|
| OK (w/o Blocking System) | A |
| OK (w/ Blocking System) | B |
| NG | C |
A
B
C
| *a | Component without harness connected(Navigation antenna cord sub-assembly) |
| *1 | Core wire |
| *2 | Shield |
Disconnect the A navigation antenna assembly connector.
Disconnect the G navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A (Core wire) - B (Core wire) | Always | Below 1 Ω |
| A (Shield) - B (Shield) | Always | Below 1 Ω |
| A (Core wire) - A (Shield) or B (Core wire) - B (Shield) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the navigation antenna assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same trouble occurs again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the instrument panel integration antenna assembly with a new or normally functioning one.
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same trouble occurs again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the divider antenna assembly with a new or normally functioning one.
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check if the same trouble occurs again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG