Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.04–2012.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  USB Device or "iPod" cannot Charge  


DESCRIPTION

This is the circuit that the navigation receiver assembly uses to supply power to devices connected to the USB jack of the No. 1 stereo jack adapter assembly. This diagnosis procedure is for when a USB device or "iPod" cannot charge.

WIRING DIAGRAM

E237859
0.354,1.917 0.594,2.073 0.24,0.156 10 false z7 1.438,1.323 1.677,1.479 0.24,0.156 10 false 4 0.969,1.417 1.375,1.573 0.406,0.156 10 false UGD1 0.99,0.646 1.385,0.802 0.396,0.156 10 false USV1 5.802,1.406 6.344,1.625 0.542,0.219 10 false UJSG 5.813,0.635 6.229,0.865 0.417,0.229 10 false UPI 1.427,0.542 1.667,0.698 0.24,0.156 10 false 1 5.604,1.344 5.823,1.521 0.219,0.177 10 false 4 5.604,0.542 5.802,0.708 0.198,0.167 10 false 1 0.354,2.073 1.625,2.417 1.271,0.344 10 false Navigation Receiver Assembly 5.542,1.917 5.781,2.073 0.24,0.156 10 false z1 5.552,2.073 6.708,2.479 1.156,0.406 10 false No. 1 Stereo Jack Adapter Assembly

PROCEDURE

1.REPLACE USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the stereo jack adapter.


b.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



c.

Turn the ignition switch to ACC.


d.

Connect a known good USB device or "iPod" to the stereo jack adapter.

OK:

USB device or "iPod" charges.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS DEFECTIVE

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
C225529
1.563,0.313 1.948,0.552 0.385,0.24 1.396,1.208 1.104,1.354 true 2.094,1.219 2.396,1.365 true 0.188,0.167 0.385,0.313 0.198,0.146 10 false *a 0.833,1.323 1.177,1.5 0.344,0.177 10 false UPI 2.458,1.323 2.875,1.531 0.417,0.208 10 false UJSG 1.667,0.344 1.979,0.531 0.313,0.188 10 false z1
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the z1 No. 1 stereo jack adapter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z1-1 (UPI) - z1-4 (UJSG) Always 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 STEREO JACK ADAPTER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the z7 navigation receiver assembly connector.


b.

Disconnect the z1 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z7-1 (USV1) - z1-1 (UPI) Always Below 1 Ω
z7-4 (UGD1) - z1-4 (UJSG) Always Below 1 Ω
z7-1 (USV1) - Body ground Always 10 kΩ or higher
z7-4 (UGD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR