Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009640 DOOR LOCK _0052680 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors cannot be Locked / Unlocked Simultaneously  


DESCRIPTION

The driver side junction block assembly drives the door lock motors according to switch signals from the door control switch of the power window regulator master switch assembly and the driver side door key cylinder.

However, the driver side door key-linked lock/unlock function will not operate when the driver side seat belt is fastened.

WIRING DIAGRAM

B294249
1.156,1.427 2.708,1.906 1.552,0.479 10 false Power Window Regulator Master Switch Assembly 0.542,3.469 0.771,3.646 0.229,0.177 10 false I2 0.135,5.031 0.313,5.208 0.177,0.177 10 false *4 1.833,5.042 2.01,5.219 0.177,0.177 10 false *5 0.542,3.635 2.469,4.01 1.927,0.375 10 false Front Door Lock Assembly LH 0.833,4.458 1.135,4.635 0.302,0.177 10 false G19 0.833,4.625 2.74,4.917 1.906,0.292 10 false Combination Meter Assembly 3.031,3.771 4.49,4.24 1.458,0.469 10 false to Door Lock Assembly (except Driver Side) 3.01,4.375 4.5,4.917 1.49,0.542 10 false to Door Lock Assembly (except Driver Side) 0.615,5.427 0.896,5.604 0.281,0.177 10 false K1 0.615,5.594 1.771,5.979 1.156,0.385 10 false Front Seat Inner Belt Assembly LH 0.052,7.563 1.156,7.813 1.104,0.25 10 false *3: for Single Cab 0.052,7.313 3.104,7.573 3.052,0.26 10 false *2: for Double Cab (w/o Jam Protection Function) 0.052,7.063 3.063,7.323 3.01,0.26 10 false *1: for Double Cab (w/ Jam Protection Function) 3.865,7.313 5.083,7.583 1.219,0.271 10 false *5: for Power Seat 3.865,7.063 5.146,7.344 1.281,0.281 10 false *4: for Manual Seat 6.083,0.677 6.552,0.854 0.469,0.177 10 false L1 5.292,0.677 5.5,0.854 0.208,0.177 10 false 2A 5.333,0.49 5.469,0.635 0.135,0.146 10 false 4 2.167,2.188 2.302,2.333 0.135,0.146 10 false 9 1.979,2.198 2.083,2.344 0.104,0.146 10 false L 1.885,2.49 2.083,2.635 0.198,0.146 10 false UL 1.979,2.844 2.083,2.99 0.104,0.146 10 false L 1.885,3.271 2.083,3.417 0.198,0.146 10 false UL 2.167,2.49 2.354,2.635 0.188,0.146 10 false 10 0.74,2.323 0.875,2.469 0.135,0.146 10 false 7 1.073,4.104 1.25,4.25 0.177,0.146 10 false 11 1.625,4.125 1.948,4.365 0.323,0.24 10 false CPU 1.302,4.104 1.635,4.323 0.333,0.219 10 false BKL 2.167,2.833 2.302,2.979 0.135,0.146 10 false 4 2.167,3.281 2.302,3.427 0.135,0.146 10 false 1 0.188,5.281 0.323,5.427 0.135,0.146 10 false 1 0.188,6.063 0.323,6.208 0.135,0.146 10 false 2 2.292,5.427 2.573,5.604 0.281,0.177 10 false P4 2.292,5.594 3.448,5.979 1.156,0.385 10 false Front Seat Inner Belt Assembly LH 1.865,5.281 2,5.427 0.135,0.146 10 false 1 1.865,6.063 2,6.208 0.135,0.146 10 false 4 5.219,5.771 6.99,6.24 1.771,0.469 10 false Driver Side Junction Block Assembly (Integration Relay) 1.708,0.719 2.115,0.958 0.406,0.24 10 false Lock 1.156,2.198 1.771,2.438 0.615,0.24 10 false Key Lock 1.156,2.656 1.875,2.875 0.719,0.219 10 false Key Unlock 1.604,1.063 2.104,1.302 0.5,0.24 10 false Unlock 2.51,0.99 2.76,1.135 0.25,0.146 10 false 8*1 2.563,1.177 2.719,1.323 0.156,0.146 10 false I5 2.865,0.99 3.115,1.135 0.25,0.146 10 false 8*2 2.885,1.177 3.115,1.323 0.229,0.146 10 false I12 3.229,0.99 3.479,1.135 0.25,0.146 10 false 5*3 2.51,0.49 2.76,0.635 0.25,0.146 10 false 5*1 2.323,0.75 2.438,0.896 0.115,0.146 10 false L 2.24,1.083 2.438,1.229 0.198,0.146 10 false UL 1.552,0.854 1.667,1 0.115,0.146 10 false E 0.927,2.323 1.042,2.469 0.115,0.146 10 false E 2.865,0.49 3.115,0.635 0.25,0.146 10 false 5*2 3.229,0.49 3.479,0.635 0.25,0.146 10 false 2*3 3.25,1.177 3.479,1.323 0.229,0.146 10 false I13 2.563,0.677 2.719,0.823 0.156,0.146 10 false I5 2.885,0.677 3.115,0.823 0.229,0.146 10 false I12 3.25,0.677 3.479,0.823 0.229,0.146 10 false I13 0.521,0.74 0.771,0.885 0.25,0.146 10 false 1*1 0.885,0.74 1.135,0.885 0.25,0.146 10 false 3*2 1.24,0.74 1.49,0.885 0.25,0.146 10 false 1*3 0.573,0.938 0.729,1.083 0.156,0.146 10 false I5 0.896,0.938 1.125,1.083 0.229,0.146 10 false I12 1.26,0.938 1.49,1.083 0.229,0.146 10 false I13 5.823,0.583 6.021,0.76 0.198,0.177 10 false 14 6.083,1.167 6.552,1.344 0.469,0.177 10 false UL1 5.281,1.177 5.49,1.354 0.208,0.177 10 false 2D 5.333,0.979 5.469,1.125 0.135,0.146 10 false 4 5.833,1.063 6.021,1.24 0.188,0.177 10 false 11 6.094,2.906 6.563,3.083 0.469,0.177 10 false ACT+ 5.292,2.927 5.5,3.104 0.208,0.177 10 false 2R 5.302,2.729 5.479,2.875 0.177,0.146 10 false 28 5.292,3.802 5.5,3.979 0.208,0.177 10 false 2K 5.292,3.594 5.469,3.74 0.177,0.146 10 false 11 5.292,4.396 5.5,4.573 0.208,0.177 10 false 2K 5.292,4.188 5.469,4.333 0.177,0.146 10 false 10 5.906,2.844 6.021,3.021 0.115,0.177 10 false 3 6.094,3.333 6.563,3.51 0.469,0.177 10 false ACT- 5.292,3.365 5.5,3.542 0.208,0.177 10 false 2R 5.302,3.156 5.479,3.302 0.177,0.146 10 false 27 5.906,3.271 6.021,3.448 0.115,0.177 10 false 2

PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Result:
Result Proceed to
No doors can be locked using power window regulator master switch assembly (door control switch) A
No doors can be locked using key-linked switch B




A

2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)

B

4.INSPECT FRONT DOOR LOCK ASSEMBLY LH
2.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DOOR CONTROL SWITCH)
a.
B294250
1.74,2.656 2.01,3.115 2.01,3.115 2.167,3.115 true 1.719,2.656 1.802,3.302 1.802,3.302 1.948,3.302 true 2.042,2.667 2.365,2.885 2.365,2.885 2.51,2.885 true 1.271,2.656 1.042,2.844 1.042,2.844 0.896,2.844 true 1.417,2.656 1.156,3.052 1.156,3.052 1.01,3.052 true 1.521,2.656 1.292,3.281 1.292,3.281 1.146,3.281 true 0.219,0.302 0.396,0.469 0.177,0.167 10 false *a 1.438,0.417 1.615,0.583 0.177,0.167 10 false *b 2.188,3.031 2.677,3.188 0.49,0.156 10 false L*A, *B 1.979,3.219 2.469,3.375 0.49,0.156 10 false UL*C 2.542,2.771 3.146,2.927 0.604,0.156 10 false UL*A, *B 0.271,2.75 0.781,2.906 0.51,0.156 10 false E*A, *C 0.667,2.958 0.948,3.115 0.281,0.156 10 false U*C 0.823,3.188 1.094,3.344 0.271,0.156 10 false E*B
*A for Double Cab (w/ Jam Protection Function)
*B for Double Cab (w/o Jam Protection Function)
*C for Single Cab
*a Lock
*b Unlock


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Double Cab (w/ Jam Protection Function):
Tester Connection Switch Condition Specified Condition
1 (E) - 5 (L) Lock Below 1 Ω
1 (E) - 5 (L), 1 (E) - 8 (UL) OFF 10 kΩ or higher
1 (E) - 8 (UL) Unlock Below 1 Ω

for Double Cab (w/o Jam Protection Function):
Tester Connection Switch Condition Specified Condition
3 (E) - 5 (L) Lock Below 1 Ω
3 (E) - 5 (L), 3 (E) - 8 (UL) OFF 10 kΩ or higher
3 (E) - 8 (UL) Unlock Below 1 Ω

for Single Cab:
Tester Connection Switch Condition Specified Condition
1 (E) - 2 (L) Lock Below 1 Ω
1 (E) - 2 (L) , 1 (E) - 5 (UL) OFF 10 kΩ or higher
1 (E) - 5 (UL) Unlock Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)
a.

Disconnect the I5*1, I12*2 or I13*3 power window regulator master switch assembly connector.

*1: for Double Cab (w/ Jam Protection Function)

*2: for Double Cab (w/o Jam Protection Function)

*3: for Single Cab



b.

Disconnect the 2A and 2D driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Double Cab (w/ Jam Protection Function):
Tester Connection Condition Specified Condition
I5-5 (L) - 2A-4 (L1) Always Below 1 Ω
I5-8 (UL) - 2D-4 (UL1) Always Below 1 Ω
I5-1 (E) - Body ground Always Below 1 Ω
I5-5 (L) or 2A-4 (L1) - Body ground Always 10 kΩ or higher
I5-8 (UL) or 2D-4 (UL1) - Body ground Always 10 kΩ or higher

for Double Cab (w/o Jam Protection Function):
Tester Connection Condition Specified Condition
I12-5 (L) - 2A-4 (L1) Always Below 1 Ω
I12-8 (UL) - 2D-4 (UL1) Always Below 1 Ω
I12-3 (E) - Body ground Always Below 1 Ω
I12-5 (L) or 2A-4 (L1) - Body ground Always 10 kΩ or higher
I12-8 (UL) or 2D-4 (UL1) - Body ground Always 10 kΩ or higher

for Single Cab:
Tester Connection Condition Specified Condition
I13-2 (L) - 2A-4 (L1) Always Below 1 Ω
I13-5 (UL) - 2D-4 (UL1) Always Below 1 Ω
I13-1 (E) - Body ground Always Below 1 Ω
I13-2 (L) or 2A-4 (L1) - Body ground Always 10 kΩ or higher
I13-5 (UL) or 2D-4 (UL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT DOOR LOCK ASSEMBLY LH
a.
B295138
1.969,2.885 1.833,3.083 1.833,3.083 1.677,3.083 true 2.302,2.865 2.438,3.125 2.438,3.125 2.594,3.125 true 2.073,2.875 2.021,3.208 2.021,3.208 1.865,3.208 true 3.031,0.365 3.198,0.51 0.167,0.146 10 *a 3.052,0.813 3.219,0.958 0.167,0.146 10 *b 2.708,1.292 2.885,1.438 0.177,0.146 10 *c 1.458,2.99 1.667,3.135 0.208,0.146 10 UL 2.615,3.052 2.74,3.198 0.125,0.146 10 E 1.74,3.135 1.854,3.281 0.115,0.146 10 L
*a Lock
*b Off
*c Unlock


Remove the front door lock assembly LH.

Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (E) - 9 (L) Lock Below 1 Ω
7 (E) - 9 (L), 7 (E) - 10 (UL) Off 10 kΩ or higher
7 (E) - 10 (UL) Unlock Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK SEAT BELT WARNING SYSTEM

NG

REPLACE FRONT DOOR LOCK ASSEMBLY LH

5.CHECK SEAT BELT WARNING SYSTEM
a.

Turn the ignition switch to ON.


b.

When the driver side seat belt is not fastened, check that the driver side seat belt warning light in the combination meter assembly blinks.


c.

When the driver side seat belt is fastened, check that the driver side seat belt warning light in the combination meter assembly turns off.

OK:

Driver side seat belt warning light blinks and turns off according to above operation.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT LH - FRONT DOOR LOCK LH)

NG

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT LH - FRONT DOOR LOCK LH)
a.

Disconnect K1*1 or P4*2 front seat inner belt assembly LH connector.

*1: for Manual Seat

*2: for Power Seat



b.

Disconnect the I2 front door lock assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Seat:
Tester Connection Condition Specified Condition
K1-1 - I2-7 (E) Always Below 1 Ω
K1-1 or I2-7 (E) - Body ground Always 10 kΩ or higher

for Power Seat:
Tester Connection Condition Specified Condition
P4-1 - I2-7 (E) Always Below 1 Ω
P4-1 or I2-7 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK LH - DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK LH - DRIVER SIDE JUNCTION BLOCK AND BODY GROUND)
a.

Disconnect the I2 front door lock assembly LH connector.


b.

Disconnect the 2A and 2D driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-10 (UL) - 2D-4 (UL1) Always Below 1 Ω
I2-9 (L) - 2A-4 (L1) Always Below 1 Ω
I2-7 (E) - Body ground Driver seat belt is not fastened Below 1 Ω
I2-10 (UL) or 2D-4 (UL1) - Body ground Always 10 kΩ or higher
I2-9 (L) or 2A-4 (L1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR