Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) › 2012.04–2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052778 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Driver Side Power Window Manual Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front power window regulator motor assembly LH or wire harness.

WIRING DIAGRAM

B276858
4.979,0.781 5.167,1.01 0.188,0.229 10 false U 4.969,3.042 6.531,3.479 1.563,0.438 10 false Power Window Regulator Master Switch Assembly 0.281,0.698 2.188,1.156 1.906,0.458 10 false Front Power Window Regulator Motor Assembly LH 1.24,1.688 2.24,1.906 1,0.219 10 false from IG1 Relay 0.646,2.052 1.458,2.271 0.813,0.219 10 false from Battery 3.417,1.865 3.813,2.063 0.396,0.198 10 false PWR 4.99,1.698 5.167,1.896 0.177,0.198 10 false B 4.979,2.073 5.302,2.271 0.323,0.198 10 false BW 4.969,2.448 5.146,2.667 0.177,0.219 10 false E 4.979,1.115 5.156,1.313 0.177,0.198 10 false D 0.281,0.542 0.563,0.708 0.281,0.167 10 false I3 3.396,0.656 3.573,0.813 0.177,0.156 10 false 2 3.396,0.979 3.573,1.135 0.177,0.156 10 false 1 4.969,2.896 5.229,3.083 0.26,0.188 10 false I5 4.792,0.667 4.948,0.813 0.156,0.146 10 false 4 4.802,0.99 4.948,1.135 0.146,0.146 10 false 9 4.792,1.594 4.927,1.74 0.135,0.146 10 false 6 4.792,1.958 4.927,2.104 0.135,0.146 10 false 7 4.792,2.333 4.927,2.479 0.135,0.146 10 false 1 3.188,0.792 3.385,1.021 0.198,0.229 10 false U 3.198,1.104 3.375,1.302 0.177,0.198 10 false D 2.563,2.219 3.042,2.417 0.479,0.198 10 false DOOR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
B276330
0.135,0.875 0.667,1.167 0.531,0.292 1.729,0.208 1.875,1.042 true 2.365,0.26 2.073,1.031 true 1.729,0.208 1.49,0.208 false 2.604,0.26 2.375,0.26 false 0.927,0.292 1.021,1.042 true 0.927,0.292 0.74,0.292 false 0.354,0.948 0.615,1.115 0.26,0.167 10 false I5 1.333,0.125 1.479,0.292 0.146,0.167 10 false B 2.646,0.177 2.948,0.354 0.302,0.177 10 false BW 0.083,0 0.281,0.188 0.198,0.188 10 false *a 0.583,0.208 0.729,0.396 0.146,0.188 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the I5 power window regulator master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I5-7 (BW) - Body ground Always 11 to 14 V
I5-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.
B276330
0.208,0.844 0.677,1.135 0.469,0.292 2.854,0.865 2.479,1.042 true 1.531,1.021 1.302,0.229 1.302,0.229 1.042,0.229 true 2.906,0.76 3.042,0.938 0.135,0.177 10 false D 0.906,0.167 1.073,0.333 0.167,0.167 10 false U 0.115,0.073 0.385,0.313 0.271,0.24 10 false *a 0.385,0.917 0.625,1.094 0.24,0.177 10 false I5
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Disconnect the I5 power window regulator master switch assembly connector.


b.

Check operation of the front power window regulator motor assembly LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → I5-4 (U)
Battery negative (-) → I5-9 (D)
Power window moves up
Battery positive (+) → I5-9 (D)
Battery negative (-) → I5-4 (U)
Power window moves down



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the I5 power window regulator master switch assembly connector.


b.

Disconnect the I3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-9 (D) - I3-1 (D) Always Below 1 Ω
I5-4 (U) - I3-2 (U) Always Below 1 Ω
I5-9 (D) or I3-1 (D) - Body ground Always 10 kΩ or higher
I5-4 (U) or I3-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR