If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front power window regulator motor assembly LH or wire harness.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
for Double Cab:
Disconnect the I12 power window regulator master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I12-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-3 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
except Double Cab:
Disconnect the I13 power window regulator master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I13-9 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I13-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
for Double Cab:
Disconnect the I12 power window regulator master switch assembly connector.
Check operation of the front power window regulator motor assembly LH.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → I12-4 (U)Battery negative (-) → I12-9 (D) | Power window moves up |
| Battery positive (+) → I12-9 (D)Battery negative (-) → I12-4 (U) | Power window moves down |
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
except Double Cab:
Disconnect the I13 power window regulator master switch assembly connector.
Check operation of the front power window regulator motor assembly LH.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → I13-3 (U)Battery negative (-) → I13-4 (D) | Power window moves up |
| Battery positive (+) → I13-4 (D)Battery negative (-) → I13-3 (U) | Power window moves down |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I12*1 or I13*2 power window regulator master switch assembly connector.
*1: for Double Cab
*2: except Double Cab
Disconnect the I3 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-9 (D) - I3-1 (D) | Always | Below 1 Ω |
| I12-4 (U) - I3-2 (U) | Always | Below 1 Ω |
| I12-9 (D) or I3-1 (D) - Body ground | Always | 10 kΩ or higher |
| I12-4 (U) or I3-2 (U) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I13-4 (D) - I3-1 (D) | Always | Below 1 Ω |
| I13-3 (U) - I3-2 (U) | Always | Below 1 Ω |
| I13-9 (D) or I3-1 (D) - Body ground | Always | 10 kΩ or higher |
| I13-3 (U) or I3-2 (U) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG