If the front passenger side manual up/down function does not operate, a malfunction may be present in the front power window regulator motor assembly RH, front power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *a | Front view of wire harness connector
(to front power window regulator switch assembly RH) |
Disconnect the H5 front power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H5-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front power window regulator switch assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (D) - 4 (SD) | UP | Below 1 Ω |
| 2 (U) - 3 (B) | ||
| 5 (D) - 4 (SD) | OFF | Below 1 Ω |
| 2 (U) - 1 (SU) | ||
| 5 (D) - 3 (B) | DOWN | Below 1 Ω |
| 2 (U) - 1 (SU) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H5 front power window regulator switch assembly RH connector.
Disconnect the H2 front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H5-5 (D) - H2-1 (D) | Always | Below 1 Ω |
| H5-2 (U) - H2-2 (U) | Always | Below 1 Ω |
| H5-5 (D) or H2-1 (D) - Body ground | Always | 10 kΩ or higher |
| H5-2 (U) or H2-2 (U) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Motor Gear |
|
Clockwise |
|
Counterclockwise |
Remove the front power window regulator motor assembly RH.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL
Apply battery voltage to connector terminals 1 (D) and 2 (U).
Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U) |
Motor gear rotates clockwise |
| Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D) |
Motor gear rotates counterclockwise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I12*1 or I13*2 power window regulator master switch assembly connector.
*1: for Double Cab
*2: except Double Cab
Disconnect the H5 front power window regulator switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I12-18 (U) - H5-1 (SU) | Always | Below 1 Ω |
| I12-15 (D) - H5-4 (SD) | Always | Below 1 Ω |
| I12-18 (U) or H5-1 (SU) - Body ground | Always | 10 kΩ or higher |
| I12-15 (D) or H5-4 (SD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I13-8 (U) - H5-1 (SU) | Always | Below 1 Ω |
| I13-10 (D) - H5-4 (SD) | Always | Below 1 Ω |
| I13-8 (U) or H5-1 (SU) - Body ground | Always | 10 kΩ or higher |
| I13-10 (D) or H5-4 (SD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG