Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) › from 2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052792 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the front passenger side manual up/down function does not operate, a malfunction may be present in the front power window regulator motor assembly RH, front power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

B276859
2.01,3.969 2.177,4.167 0.167,0.198 10 false E 2.01,2.688 2.177,2.885 0.167,0.198 10 false B 2.01,3.042 2.198,3.24 0.188,0.198 10 false U 0.458,4.667 2.021,5.115 1.563,0.448 10 false Power Window Regulator Master Switch Assembly 5.052,3.969 6.969,4.438 1.917,0.469 10 false Front Power Window Regulator Switch Assembly RH 0.354,0.531 2.365,0.938 2.01,0.406 10 false Front Power Window Regulator Motor Assembly RH 0.229,1.646 1.24,1.906 1.01,0.26 10 false from IG1 Relay 2.365,1.813 2.76,2.01 0.396,0.198 10 false PWR 2.01,3.344 2.198,3.542 0.188,0.198 10 false D 0.365,0.365 0.573,0.563 0.208,0.198 10 false H2 0.479,4.51 1.604,4.708 1.125,0.198 10 false I12*1, I13*2 2.219,2.917 2.906,3.135 0.688,0.219 10 false 18*1, 8*2 2.219,3.208 2.969,3.458 0.75,0.25 10 false 15*1, 10*2 2.229,2.563 2.833,2.802 0.604,0.24 10 false 6*1, 9*2 2.229,3.854 2.896,4.125 0.667,0.271 10 false 3*1, 1*2 3.469,0.458 3.625,0.604 0.156,0.146 10 false 1 3.479,0.76 3.635,0.906 0.156,0.146 10 false 2 4.854,0.469 5.01,0.615 0.156,0.146 10 false 5 4.854,0.76 5.01,0.906 0.156,0.146 10 false 2 4.854,1.531 5.01,1.677 0.156,0.146 10 false 3 4.854,2.906 5.01,3.052 0.156,0.146 10 false 1 4.854,3.219 5.01,3.365 0.156,0.146 10 false 4 5.052,3.802 5.354,3.99 0.302,0.188 10 false H5 5.073,3.021 5.333,3.188 0.26,0.167 10 false SU 5.073,3.323 5.354,3.5 0.281,0.177 10 false SD 5.073,0.875 5.26,1.073 0.188,0.198 10 false U 5.073,0.552 5.26,0.75 0.188,0.198 10 false D 5.073,1.635 5.24,1.833 0.167,0.198 10 false B 3.281,0.865 3.469,1.063 0.188,0.198 10 false U 3.281,0.563 3.469,0.76 0.188,0.198 10 false D 5.406,5.271 7.073,5.49 1.667,0.219 10 false *2: except Double Cab 5.406,4.99 6.677,5.208 1.271,0.219 10 false *1: for Double Cab

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)
a.
B276367
0.208,0.979 0.74,1.271 0.531,0.292 1.76,1.292 1.844,1.792 false 0.073,0.031 0.281,0.219 0.208,0.188 10 false *a 0.396,1.042 0.604,1.229 0.208,0.188 10 false H5 1.813,1.802 1.958,1.958 0.146,0.156 10 false B
*a Front view of wire harness connector
(to front power window regulator switch assembly RH)


Disconnect the H5 front power window regulator switch assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H5-3 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.
B280844
1.896,0.99 2.25,0.49 2.25,0.49 2.5,0.49 true 1.573,1 1.24,0.521 1.24,0.521 1.021,0.521 true 2.01,1.031 2.354,1.031 true 1.073,1.042 1.427,1.042 true 1.729,0.979 1.74,0.229 1.74,0.229 1.885,0.229 true 2.396,0.958 2.802,1.146 0.406,0.188 10 false SU 2.531,0.417 2.802,0.604 0.271,0.188 10 false U 1.927,0.156 2.198,0.344 0.271,0.188 10 false B 0.792,0.448 1.063,0.635 0.271,0.188 10 false SD 0.948,0.969 1.104,1.156 0.156,0.188 10 false D

Remove the front power window regulator switch assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (D) - 4 (SD) UP Below 1 Ω
2 (U) - 3 (B)
5 (D) - 4 (SD) OFF Below 1 Ω
2 (U) - 1 (SU)
5 (D) - 3 (B) DOWN Below 1 Ω
2 (U) - 1 (SU)



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the H5 front power window regulator switch assembly RH connector.


b.

Disconnect the H2 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-5 (D) - H2-1 (D) Always Below 1 Ω
H5-2 (U) - H2-2 (U) Always Below 1 Ω
H5-5 (D) or H2-1 (D) - Body ground Always 10 kΩ or higher
H5-2 (U) or H2-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.
B294222
1.042,1.271 1.333,0.406 1.333,0.406 1.531,0.406 false 2.74,1.271 2.74,0.885 2.74,0.885 2.979,0.885 false 2.323,1.271 2.323,0.875 2.323,0.875 2.083,0.875 false 1.958,0.802 2.125,0.99 0.167,0.188 10 false U 1.573,0.323 1.74,0.51 0.167,0.188 10 false *1 3.021,0.802 3.177,0.99 0.156,0.188 10 false D
*1 Motor Gear
V100135

Clockwise
V100136

Counterclockwise


Remove the front power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


b.

Apply battery voltage to connector terminals 1 (D) and 2 (U).

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).



c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (D)Battery negative (-) → 2 (U) Motor gear rotates clockwise
Battery positive (+) → 2 (U)Battery negative (-) → 1 (D) Motor gear rotates counterclockwise



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Disconnect the I12*1 or I13*2 power window regulator master switch assembly connector.

*1: for Double Cab

*2: except Double Cab


b.

Disconnect the H5 front power window regulator switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Double Cab
Tester Connection Condition Specified Condition
I12-18 (U) - H5-1 (SU) Always Below 1 Ω
I12-15 (D) - H5-4 (SD) Always Below 1 Ω
I12-18 (U) or H5-1 (SU) - Body ground Always 10 kΩ or higher
I12-15 (D) or H5-4 (SD) - Body ground Always 10 kΩ or higher

except Double Cab
Tester Connection Condition Specified Condition
I13-8 (U) - H5-1 (SU) Always Below 1 Ω
I13-10 (D) - H5-4 (SD) Always Below 1 Ω
I13-8 (U) or H5-1 (SU) - Body ground Always 10 kΩ or higher
I13-10 (D) or H5-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR