Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) › 2012.04–2012.10
RM1840EF _59 Vehicle Exterior _009651 WINDOW / GLASS _0052792 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Power Windows do not Operate at All  


DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch assembly may have no power or may be malfunctioning.

WIRING DIAGRAM

B286741
4.76,0.542 4.927,0.74 0.167,0.198 10 false B 4.76,1.406 4.938,1.604 0.177,0.198 10 false E 4.802,1.99 6.375,2.552 1.573,0.563 10 false Power Window Regulator Master Switch Assembly 3.26,0.708 3.667,0.906 0.406,0.198 10 false PWR 4.813,1.823 5.917,2.01 1.104,0.188 10 false I12*1, I13*2 4.115,0.448 4.667,0.646 0.552,0.198 10 false 6*1, 9*2 4.115,1.302 4.656,1.51 0.542,0.208 10 false 3*1, 1*2 1.135,0.531 2.177,0.76 1.042,0.229 10 false from IG1 Relay 0.167,2.323 1.688,2.573 1.521,0.25 10 false *2: except Double Cab 0.167,2.021 1.458,2.229 1.292,0.208 10 false *1: for Double Cab

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
B276330
0.135,0.875 0.667,1.167 0.531,0.292 2.177,0.229 1.948,1.031 false 2.396,0.229 2.177,0.229 false 1.188,0.229 1.365,1.031 false 1.188,0.229 1,0.229 false 0.292,0.948 0.604,1.115 0.313,0.167 10 false I12 2.438,0.146 2.625,0.323 0.188,0.177 10 false B 0.083,0.042 0.281,0.229 0.198,0.188 10 false *a 0.854,0.156 1,0.344 0.146,0.188 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


for Double Cab:

i.

Disconnect the I12 power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I12-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-3 (E) - Body ground Always Below 1 Ω




b.
B290653
0.094,0.74 0.625,1.031 0.531,0.292 2.427,1 2.521,0.396 2.521,0.396 2.688,0.396 false 1.51,1.448 1.646,1.99 1.646,1.99 1.854,1.99 false 0.25,0.802 0.51,0.969 0.26,0.167 10 false I13 1.906,1.906 2.042,2.115 0.135,0.208 10 false B 0.094,0.104 0.281,0.281 0.188,0.177 10 false *a 2.76,0.313 2.938,0.479 0.177,0.167 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


except Double Cab:

i.

Disconnect the I13 power window regulator master switch assembly connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I13-9 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-1 (E) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR