Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  11  Room Temperature Sensor Circuit  


DESCRIPTION

The cooler thermistor is installed in the instrument panel to detect the room temperature and control the heater and air conditioning AUTO function. The resistance of the cooler thermistor changes in accordance with the room temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the cooler thermistor and reads voltage changes as the resistance of the cooler thermistor changes.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
11 Room Temperature Sensor Circuit An open or short in the room temperature sensor circuit.
·

Cooler thermistor

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(8.5 min. or more)
If the room temperature is approximately -18.6°C (1.48°F) or lower, DTC 11 may be output even though the system is normal. even though the system is normal.

WIRING DIAGRAM

E227733
5.51,0.76 5.781,0.927 0.271,0.167 10 false TR 0.927,1.448 1.406,1.594 0.479,0.146 10 false G76 5.271,2.74 5.75,2.885 0.479,0.146 10 false G95 5.292,2.104 5.479,2.25 0.188,0.146 10 false 13 5.271,0.646 5.458,0.792 0.188,0.146 10 false 18 2.427,1.219 2.552,1.365 0.125,0.146 10 false 2 2.427,1.833 2.552,1.979 0.125,0.146 10 false 1 5.51,2.208 5.927,2.365 0.417,0.156 10 false SG-3 5.292,2.906 6.854,3.583 1.563,0.677 10 false Air Conditioning Amplifier Assembly 0.948,1.615 2.219,1.854 1.271,0.24 10 false Cooler Thermistor

PROCEDURE

1.INSPECT COOLER THERMISTOR
a.
E272296
0.083,1.604 0.396,1.802 0.313,0.198 10 false *a 0.083,1.958 0.396,2.156 0.313,0.198 10 false 4.0 0.073,2.229 0.385,2.427 0.313,0.198 10 false 3.5 0.073,2.469 0.385,2.667 0.313,0.198 10 false 3.0 0.083,2.719 0.396,2.917 0.313,0.198 10 false 2.5 0.083,2.958 0.396,3.156 0.313,0.198 10 false 2.0 0.073,3.229 0.385,3.427 0.313,0.198 10 false 1.5 0.073,3.479 0.385,3.677 0.313,0.198 10 false 1.0 0.083,3.719 0.396,3.917 0.313,0.198 10 false 0.5 0.083,3.969 0.396,4.167 0.313,0.198 10 false 0.0 0.323,4.052 0.635,4.25 0.313,0.198 10 false 10 0.771,4.052 1.083,4.25 0.313,0.198 10 false 20 1.281,4.052 1.594,4.25 0.313,0.198 10 false 30 1.802,4.052 2.115,4.25 0.313,0.198 10 false 40 2.813,4.052 3.125,4.25 0.313,0.198 10 false 60 2.313,4.063 2.625,4.26 0.313,0.198 10 false 50 0.323,4.229 0.635,4.427 0.313,0.198 10 false 50 0.771,4.219 1.083,4.417 0.313,0.198 10 false 68 1.271,4.219 1.583,4.417 0.313,0.198 10 false 86 1.792,4.219 2.104,4.417 0.313,0.198 10 false 104 2.302,4.219 2.615,4.417 0.313,0.198 10 false 122 2.802,4.219 3.115,4.417 0.313,0.198 10 false 140 3.073,4.042 3.385,4.24 0.313,0.198 10 false (°C) 3.083,4.219 3.396,4.417 0.313,0.198 10 false (°F) 1.552,4.365 1.865,4.563 0.313,0.198 10 false *b
*a Resistance (kΩ)
*b Temperature


Remove the cooler thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 10°C (50°F) 3.00 to 3.73 kΩ
15°C (59°F) 2.45 to 2.88 kΩ
20°C (68°F) 1.95 to 2.30 kΩ
25°C (77°F) 1.60 to 1.80 kΩ
30°C (86°F) 1.28 to 1.47 kΩ
35°C (95°F) 1.00 to 1.22 kΩ
40°C (104°F) 0.80 to 1.00 kΩ
45°C (113°F) 0.65 to 0.85 kΩ
50°C (122°F) 0.50 to 0.70 kΩ
55°C (131°F) 0.44 to 0.60 kΩ
60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Even slightly touching the thermistor may change the resistance value. Be sure to hold the connector of the thermistor.

·

When measuring the resistance, the thermistor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (Refer to the graph).



Result:
Proceed to
OK
NG



OK

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
2.115,0.052 2.583,0.302 0.469,0.25 2.885,1.198 3.052,1.583 true 2.219,0.99 1.76,1.573 true 2.198,0.094 2.563,0.271 0.365,0.177 10 G95 3.083,1.583 3.333,1.771 0.25,0.188 10 TR 0.094,0.063 0.313,0.26 0.219,0.198 10 *a 1.563,1.583 1.948,1.771 0.385,0.188 10 SG-3
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G95-18 (TR) - G95-13 (SG-3)
·

Ignition switch ON

·

Cabin temperature 25°C (77°F)


1.8 to 2.2 V
·

Ignition switch ON

·

Cabin temperature 40°C (104°F)


1.2 to 1.6 V


HINT:

As the temperature increases, the voltage decreases.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLER THERMISTOR)
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLER THERMISTOR)
a.

Disconnect the G95 air conditioning amplifier assembly connector.


b.

Disconnect the G76 cooler thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G95-18 (TR) - G76-2 Always Below 1 Ω
G95-13 (SG-3) - G76-1
G95-18 (TR) - Body ground Always 10 kΩ or higher
G95-13 (SG-3) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR