Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly connected to the accessory meter detects fluctuations in the ambient temperature. This information is used for controlling the interior temperature. The accessory meter detects the resistance of the thermistor assembly and sends this information to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
12 Ambient Temperature Sensor Circuit An open or short in ambient temperature sensor circuit
·

Thermistor assembly

·

Accessory meter assembly

·

Air conditioning amplifier assembly

·

Harness or connector


- -

WIRING DIAGRAM

E227734
5.771,0.844 6.219,1.042 0.448,0.198 10 TAMO 3.688,1.948 5.063,2.188 1.375,0.24 10 Thermistor Assembly 0.177,2.854 1.875,3.271 1.698,0.417 10 Accessory Meter Assembly 0.792,0.833 1.24,1.031 0.448,0.198 10 DATA 0.906,1.323 1.229,1.521 0.323,0.198 10 TH+ 0.938,2.333 1.219,2.531 0.281,0.198 10 SG 3.688,1.781 3.99,1.927 0.302,0.146 10 A22 5.521,2.677 5.927,2.823 0.406,0.146 10 G94 5.531,0.74 5.719,0.885 0.188,0.146 10 18 1.219,0.75 1.333,0.896 0.115,0.146 10 9 1.229,1.229 1.344,1.375 0.115,0.146 10 3 0.156,2.708 0.719,2.854 0.563,0.146 10 G32 1.229,2.219 1.344,2.365 0.115,0.146 10 2 3.448,1.448 3.573,1.594 0.125,0.146 10 2 3.448,2.219 3.573,2.365 0.125,0.146 10 1 5.51,2.875 7.146,3.552 1.635,0.677 10 Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the accessory meter assembly illuminates normally before performing the following inspection procedure.


PROCEDURE

1.CHECK ACCESSORY METER ASSEMBLY
a.

Check the difference between the ambient temperature value displayed on the accessory meter assembly and the actual ambient temperature.

OK:

The ambient temperature displayed on the accessory meter assembly and the actual ambient temperature are almost the same.


HINT:

The temperature displayed on the accessory meter assembly and the actual temperature detected by the thermistor assembly may differ when the ambient temperature changes significantly (for example, when the vehicle is entering/exiting tunnels, or the vehicle speed or wind direction changes).



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - AIR CONDITIONING AMPLIFIER)

NG

3.INSPECT THERMISTOR ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G32 accessory meter assembly connector.


b.

Disconnect the G94 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-9 (DATA) - G94-18 (TAMO) Always Below 1 Ω
G32-9 (DATA) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THERMISTOR ASSEMBLY
a.
E272297
0.073,1.479 0.385,1.677 0.313,0.198 10 false *a 0.094,1.948 0.406,2.146 0.313,0.198 10 false 4.0 0.083,2.229 0.396,2.427 0.313,0.198 10 false 3.5 0.094,2.479 0.406,2.677 0.313,0.198 10 false 3.0 0.094,2.729 0.406,2.927 0.313,0.198 10 false 2.5 0.094,2.979 0.406,3.177 0.313,0.198 10 false 2.0 0.073,3.229 0.385,3.427 0.313,0.198 10 false 1.5 0.073,3.479 0.385,3.677 0.313,0.198 10 false 1.0 0.073,3.698 0.385,3.896 0.313,0.198 10 false 0.5 0.083,3.969 0.396,4.167 0.313,0.198 10 false 0.0 0.354,4.135 0.667,4.333 0.313,0.198 10 false 10 0.354,4.302 0.667,4.5 0.313,0.198 10 false 50 0.771,4.135 1.083,4.333 0.313,0.198 10 false 20 1.292,4.135 1.604,4.333 0.313,0.198 10 false 30 1.802,4.135 2.115,4.333 0.313,0.198 10 false 40 2.323,4.135 2.635,4.333 0.313,0.198 10 false 50 2.771,4.135 3.083,4.333 0.313,0.198 10 false 60 0.771,4.302 1.083,4.5 0.313,0.198 10 false 68 1.292,4.302 1.604,4.5 0.313,0.198 10 false 86 1.792,4.302 2.104,4.5 0.313,0.198 10 false 104 2.302,4.302 2.615,4.5 0.313,0.198 10 false 122 2.771,4.302 3.083,4.5 0.313,0.198 10 false 140 3.094,4.115 3.406,4.313 0.313,0.198 10 false (°C) 3.104,4.302 3.417,4.5 0.313,0.198 10 false (°F) 1.573,4.458 1.885,4.656 0.313,0.198 10 false *b
*a Resistance (kΩ)
*b Temperature


Remove the thermistor assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 10°C (50°F) 3.00 to 3.73 kΩ
15°C (59°F) 2.45 to 2.88 kΩ
20°C (68°F) 1.95 to 2.30 kΩ
25°C (77°F) 1.60 to 1.80 kΩ
30°C (86°F) 1.28 to 1.47 kΩ
35°C (95°F) 1.00 to 1.22 kΩ
40°C (104°F) 0.80 to 1.00 kΩ
45°C (113°F) 0.65 to 0.85 kΩ
50°C (122°F) 0.50 to 0.70 kΩ
55°C (131°F) 0.44 to 0.60 kΩ
60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Even slightly touching the thermistor assembly may change the resistance value. Be sure to hold the connector of the thermistor assembly.

·

When measuring the resistance, the thermistor assembly temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (Refer to the graph).



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - THERMISTOR)

NG

4.CHECK HARNESS AND CONNECTOR (ACCESSORY METER - THERMISTOR)
a.

Disconnect the G32 accessory meter assembly connector.


b.

Disconnect the A22 thermistor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-3 (TH+) - A22-2 Always Below 1 Ω
G32-2 (SG) - A22-1
G32-3 (TH+) - Body ground Always 10 kΩ or higher
G32-2 (SG) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE ACCESSORY METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR