Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioning unit. It detects the temperature of the cooled air that has passed through the evaporator which is then used in air conditioning control. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This thermistor is used for frost prevention.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
13 Evaporator Temperature Sensor Circuit An open or short in evaporator temperature sensor circuit
·

No. 1 cooler thermistor

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(8.5 min. or more)
-

WIRING DIAGRAM

E227735
5.25,2.688 5.781,2.833 0.531,0.146 10 G95 2.365,1.208 2.49,1.354 0.125,0.146 10 1 2.365,1.885 2.49,2.031 0.125,0.146 10 2 5.25,2.865 6.885,3.542 1.635,0.677 10 Air Conditioning Amplifier Assembly 5.521,0.781 5.792,0.948 0.271,0.167 10 TE 1.333,1.354 1.719,1.5 0.385,0.146 10 G30 5.292,2.115 5.479,2.26 0.188,0.146 10 14 5.354,0.646 5.479,0.792 0.125,0.146 10 1 5.51,2.229 5.927,2.385 0.417,0.156 10 SG-4 1.354,1.51 2.198,1.885 0.844,0.375 10 No. 1 Cooler Thermistor

PROCEDURE

1.INSPECT NO. 1 COOLER THERMISTOR
a.
E272298
0.188,1.865 0.5,2.063 0.313,0.198 10 false *a 0.125,2.094 0.438,2.292 0.313,0.198 10 false 10.0 0.146,2.281 0.458,2.479 0.313,0.198 10 false 9.0 0.156,2.5 0.469,2.698 0.313,0.198 10 false 8.0 0.156,2.688 0.469,2.885 0.313,0.198 10 false 7.0 0.156,2.885 0.469,3.083 0.313,0.198 10 false 6.0 0.167,3.073 0.479,3.271 0.313,0.198 10 false 5.0 0.167,3.271 0.479,3.469 0.313,0.198 10 false 4.0 0.167,3.458 0.479,3.656 0.313,0.198 10 false 3.0 0.156,3.656 0.469,3.854 0.313,0.198 10 false 2.0 0.156,3.865 0.469,4.063 0.313,0.198 10 false 1.0 0.167,4.042 0.479,4.24 0.313,0.198 10 false 0.0 0.417,4.167 0.729,4.365 0.313,0.198 10 false -10 1.083,4.167 1.396,4.365 0.313,0.198 10 false 0 1.688,4.167 2,4.365 0.313,0.198 10 false 10 2.333,4.167 2.646,4.365 0.313,0.198 10 false 20 2.958,4.167 3.167,4.333 0.208,0.167 10 false 30 0.458,4.323 0.771,4.521 0.313,0.198 10 false 14 1.073,4.323 1.385,4.521 0.313,0.198 10 false 32 1.688,4.323 2,4.521 0.313,0.198 10 false 50 2.333,4.323 2.646,4.521 0.313,0.198 10 false 68 2.958,4.323 3.167,4.49 0.208,0.167 10 false 86 3.156,4.156 3.417,4.354 0.26,0.198 10 false (°C) 3.167,4.333 3.427,4.531 0.26,0.198 10 false (°F) 1.906,4.469 2.219,4.667 0.313,0.198 10 false *b
*a Resistance (kΩ)
*b Temperature


Remove the No. 1 cooler thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


NOTICE:
·

Even slightly touching the No. 1 cooler thermistor may change the resistance value. Be sure to hold the connector of the No. 1 cooler thermistor.

·

When measuring the resistance, the No. 1 cooler thermistor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (Refer to the graph).



Result:
Proceed to
OK
NG



OK

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E225456
2.115,0.052 2.583,0.302 0.469,0.25 2.823,0.698 3.031,0.26 true 2.083,1 1.708,1.583 true 2.229,0.094 2.74,0.271 0.51,0.177 10 G95 3.052,0.115 3.302,0.302 0.25,0.188 10 TE 0.083,0.135 0.302,0.333 0.219,0.198 10 *a 1.531,1.583 1.896,1.771 0.365,0.188 10 SG-4
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G95-1 (TE) - G95-14 (SG-4)
·

Ignition switch ON

·

Evaporator temperature 0°C (32°F)


2.0 to 2.4 V
·

Ignition switch ON

·

Evaporator temperature 15°C (59°F)


1.4 to 1.8 V


HINT:

As the temperature increases, the voltage decreases.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - NO. 1 COOLER THERMISTOR)
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - NO. 1 COOLER THERMISTOR)
a.

Disconnect the G95 air conditioning amplifier assembly connector.


b.

Disconnect the G30 No. 1 cooler thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G95-1 (TE) - G30-1 Always Below 1 Ω
G95-14 (SG-4) - G30-2
G95-1 (TE) - Body ground Always 10 kΩ or higher
G95-14 (SG-4) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR