Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2012.10
RM1840EF _58 Vehicle Interior _009648 HEATING / AIR CONDITIONING _0052762 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  43  Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The mode damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the mode damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the mode damper to any position, which controls the mode changes.

HINT:

This DTC is also output if the mode damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the mode damper and damper link are not defective or damaged.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
43 Air Outlet Damper Control Servo Motor Circuit The mode damper position does not change when the air conditioning amplifier assembly operates the mode damper servo sub-assembly.
·

Mode damper servo sub-assembly

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(30 sec. or more)
-

WIRING DIAGRAM

E233156E08
5.333,0.917 5.667,1.063 0.333,0.146 10 false G95 1.75,0.792 1.865,0.938 0.115,0.146 10 false 2 1.76,1.313 1.875,1.458 0.115,0.146 10 false 3 1.76,1.865 1.875,2.01 0.115,0.146 10 false 1 1.75,2.375 1.865,2.521 0.115,0.146 10 false 5 1.75,2.917 1.865,3.063 0.115,0.146 10 false 4 5.323,1.438 5.656,1.583 0.333,0.146 10 false G95 5.406,1.208 5.583,1.354 0.177,0.146 10 false 25 5.385,0.698 5.563,0.844 0.177,0.146 10 false 26 5.323,1.969 5.656,2.115 0.333,0.146 10 false G95 5.385,1.76 5.563,1.906 0.177,0.146 10 false 11 5.323,2.49 5.656,2.635 0.333,0.146 10 false G94 5.427,2.281 5.573,2.427 0.146,0.146 10 false 3 5.323,3.021 5.656,3.167 0.333,0.146 10 false G94 5.448,2.813 5.604,2.958 0.156,0.146 10 false 4 1.302,0.76 1.74,0.927 0.438,0.167 10 false FDEF 1.281,1.292 1.688,1.469 0.406,0.177 10 false HEAT 1.458,1.875 1.708,2.052 0.25,0.177 10 false SG 1.302,2.344 1.74,2.521 0.438,0.177 10 false FACE 1.375,2.917 1.719,3.083 0.344,0.167 10 false DEF 5.688,0.948 6.01,1.115 0.323,0.167 10 false POA 0.229,3.448 0.677,3.615 0.448,0.167 10 false G79 5.677,1.438 6,1.615 0.323,0.177 10 false POB 5.677,1.99 6.042,2.167 0.365,0.177 10 false SG-2 5.698,2.469 6.042,2.646 0.344,0.177 10 false AOF 5.677,3.042 6.021,3.208 0.344,0.167 10 false AOD 5.396,3.438 6.979,4.031 1.583,0.594 10 false Air Conditioning Amplifier Assembly 0.219,3.615 2.573,3.844 2.354,0.229 10 false Mode Damper Servo Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

When DTC 41, 42 and 43 are output at same time, there would be malfunctioning on power source circuit.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>Back-up Power Source Circuit


PROCEDURE

1.PERFORM ACTUATOR CHECK
a.

Warm up the engine.



c.

Place your hand in front of a vent and check that the mode damper position changes according to the display code.

Display Code Mode Damper Position
0 FACE
1 FACE
2 FACE
3 FACE
4 FACE
5 BI-LEVEL
6 FOOT
7 FOOT
8 FOOT/DEF
9 DEF

OK:

Mode damper position changes in accordance with each display code.


HINT:

The progression through the steps of the actuator check can be changed from automatic to manual by pressing the front DEF switch.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

2.CHECK HARNESS AND CONNECTOR (MODE DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
2.CHECK HARNESS AND CONNECTOR (MODE DAMPER SERVO - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G79 mode damper servo sub-assembly connector.


b.

Disconnect the G94 and G95 air conditioning amplifier assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-4 (DEF) - G94-4 (AOD) Always Below 1 Ω
G79-5 (FACE) - G94-3 (AOF)
G79-2 (FDEF) - G95-26 (POA)
G79-3 (HEAT) - G95-25 (POB)
G79-1 (SG) - G95-11 (SG-2)
G79-4 (DEF) - Body ground Always 10 kΩ or higher
G79-5 (FACE) - Body ground
G79-2 (FDEF) - Body ground
G79-3 (HEAT) - Body ground
G79-1 (SG) - Body ground



Result:
Proceed to
OK
NG



OK

3.REPLACE MODE DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE MODE DAMPER SERVO SUB-ASSEMBLY
a.

Temporally replace the mode damper servo sub-assembly with a new or normally functioning one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY


b.

Check the mode damper operates normally.

OK:

Mode damper operates normally.



Result:
Proceed to
OK
NG



OK

END (MODE DAMPER SERVO IS DEFECTIVE)

NG