Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned on (IG), the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A255258
0.99,0.917 1.354,1.094 0.365,0.177 10 false G9 0.99,1.073 2.156,1.438 1.167,0.365 10 false Ignition Switch 3.427,3.063 4.677,3.271 1.25,0.208 10 false Combination Meter 3.604,2.625 4.01,2.875 0.406,0.25 10 false MIL 6.375,3.406 6.771,3.646 0.396,0.24 10 false ECM 6.208,2.458 6.458,2.698 0.25,0.24 10 false W 2.583,1.479 3.083,1.75 0.5,0.271 10 false MET 0.833,2.667 1.552,3.135 0.719,0.469 10 false Battery 0.688,1.479 1.188,1.75 0.5,0.271 10 false AM2 1.781,0.667 2.125,0.938 0.344,0.271 10 false IG2 1.094,0.667 1.521,0.948 0.427,0.281 10 false AM2 2.104,0.469 2.344,0.719 0.24,0.25 10 false 6 0.948,0.469 1.156,0.719 0.208,0.25 10 false 5 5.938,2.385 6.167,2.604 0.229,0.219 10 false 19 6.375,3.281 6.76,3.469 0.385,0.188 10 false G149 4.823,2.385 5.115,2.615 0.292,0.229 10 false 39 3.063,2.385 3.344,2.594 0.281,0.208 10 false 21 3.427,2.927 3.854,3.073 0.427,0.146 10 false G19 4.396,2.375 4.833,2.594 0.438,0.219 10 false CHK 3.333,2.365 3.698,2.594 0.365,0.229 10 false IG+

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check the MIL illumination condition.

Result:
Condition Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if DTCs have been stored (Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR). If DTCs are output, write them down.

Powertrain > Engine > Trouble Codes
50001 61

d.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Check that the MIL turns off.

OK:

MIL turns off.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-39 (CHK) - G149-19 (W) Always Below 1 Ω
G19-39 (CHK) or G149-19 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination assembly meter connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.



Result:
Proceed to
OK
NG



OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

Refer to the combination meter troubleshooting procedure.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)