Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the meter.

WIRING DIAGRAM

E224860
0.365,2.125 1.646,2.302 1.281,0.177 10 false from Ignition Switch 0.854,1.365 1.646,1.542 0.792,0.177 10 false from Battery 3.656,1.521 4.104,1.698 0.448,0.177 10 false DOME 2.813,1.51 3.198,1.688 0.385,0.177 10 false DCC 3.208,2.26 3.625,2.438 0.417,0.177 10 false MET 4.781,1.25 4.927,1.396 0.146,0.146 10 false 1 4.573,5.438 6.427,5.615 1.854,0.177 10 false Combination Meter Assembly 4.729,3.26 4.906,3.406 0.177,0.146 10 false 22 4.729,1.979 4.927,2.125 0.198,0.146 10 false 21 4.573,5.25 4.865,5.396 0.292,0.146 10 false G19 5.021,1.385 5.156,1.552 0.135,0.167 10 false B 5.021,2.125 5.292,2.292 0.271,0.167 10 false IG+ 5.021,3.406 5.25,3.573 0.229,0.167 10 false EP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E224604
0.135,1.281 0.625,1.583 0.49,0.302 0.823,1.438 0.813,0.635 0.813,0.635 0.719,0.635 true 0.813,1.615 1.021,1.917 1.021,1.917 1.115,1.917 true 0.917,1.542 1.135,0.563 1.135,0.563 1.219,0.563 true 0.073,0.063 0.25,0.229 0.177,0.167 10 false *a 0.583,0.552 0.708,0.719 0.125,0.167 10 false B 1.281,0.49 1.5,0.656 0.219,0.167 10 false EP 1.167,1.844 1.521,2.01 0.354,0.167 10 false IG+ 0.25,1.344 0.552,1.5 0.302,0.156 10 false G19
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the G19 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-22 (EP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G19-1 (B) - Body ground Always 11 to 14 V
G19-21 (IG+) - Body ground Ignition switch ON 11 to 14 V
G19-21 (IG+) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR