Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter receives vehicle speed signals from the speedometer sensor via the direct line.

WIRING DIAGRAM

E225467
5.708,2.854 6.99,3.219 1.281,0.365 10 false Combination Meter Assembly 0.125,3.177 1.573,3.385 1.448,0.208 10 false Speedometer Sensor 0.125,2.979 0.406,3.135 0.281,0.156 10 false C38 5.708,2.677 6,2.844 0.292,0.167 10 false G19 1.229,0.521 1.417,0.688 0.188,0.167 10 false 3 5.604,0.531 5.792,0.698 0.188,0.167 10 false 5 5.552,1.438 5.74,1.604 0.188,0.167 10 false 31 1.229,1.448 1.417,1.615 0.188,0.167 10 false 1 1.24,2.417 1.427,2.583 0.188,0.167 10 false 2 5.854,0.625 6.031,0.781 0.177,0.156 10 false SI 5.854,1.552 6.26,1.771 0.406,0.219 10 false MS5 0.958,0.646 1.188,0.844 0.229,0.198 10 false SI 0.885,1.531 1.135,1.688 0.25,0.156 10 false IG+ 0.917,2.531 1.229,2.823 0.313,0.292 10 false SE

PROCEDURE

1.CHECK SPEEDOMETER SENSOR (OUTPUT SIGNAL)
a.
E224603
1.229,0.563 1.708,0.906 0.479,0.344 2.396,0.635 2.313,0.635 2.313,0.635 1.885,1.417 true 2.896,3.625 3.25,3.823 0.354,0.198 10 false GND 2.448,0.552 2.802,0.75 0.354,0.198 10 false SI 1.333,0.656 1.635,0.854 0.302,0.198 10 false G19 0.292,0.625 0.469,0.823 0.177,0.198 10 false *a
*a Component with harness connected
(Combination Meter Assembly)


Remove the combination meter assembly with the connector(s) still connected.


b.

Using an oscilloscope, check the signal waveform of the meter.

Measurement Condition
Item Content
Tester Connection G19-5 (SI) - Body ground
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving at approximately 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength shortens.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK TRANSMISSION TYPE
2.CHECK TRANSMISSION TYPE
a.

Check the transmission type.

Result:
Result Proceed to
for Automatic Transmission A
for Manual Transmission B




A

3.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C38 speedometer sensor connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-5 (SI) - C38-3 (SI) Always Below 1 Ω
G19-31 (MS5) - C38-1 (IG+) Always Below 1 Ω
C38-1 (IG+) - C38-2 (SE) Always 10 kΩ or higher
C38-1 (IG+) - C38-3 (SI) Always 10 kΩ or higher
C38-2 (SE) - C38-3 (SI) Always 10 kΩ or higher
C38-2 (SE) - Body ground Always Below 1 Ω


Result:
Result Proceed to
NG A
OK (for 340F) B
OK (for 343E) C
OK (for 343F) D
OK (for 750F) E




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

D

E

4.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C38 speedometer sensor connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-5 (SI) - C38-3 (SI) Always Below 1 Ω
G19-31 (MS5) - C38-1 (IG+) Always Below 1 Ω
C38-1 (IG+) - C38-2 (SE) Always 10 kΩ or higher
C38-1 (IG+) - C38-3 (SI) Always 10 kΩ or higher
C38-2 (SE) - C38-3 (SI) Always 10 kΩ or higher
C38-2 (SE) - Body ground Always Below 1 Ω


Result:
Result Proceed to
NG A
OK (for VF2A) B
OK (for R150F, R151F, R156F) C
OK (for R150, R151, R156) D




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

REPLACE SPEEDOMETER SENSOR

D