Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine speed signals from the ECM. The meter CPU displays the engine speed, which is calculated based on the data received from the ECM.

WIRING DIAGRAM

E252854
1,1.927 1.365,2.125 0.365,0.198 10 false ECM 5.427,2.156 6.625,2.625 1.198,0.469 10 false Combination Meter Assembly 0.115,2.542 1.052,2.74 0.938,0.198 10 false *1: for 2TR-FE 0.115,3.344 1.073,3.542 0.958,0.198 10 false *3: for 1GR-FE 1.281,1.198 1.719,1.396 0.438,0.198 10 false TACH 1.833,1.219 2.125,1.417 0.292,0.198 10 false G88 5.438,1.979 5.729,2.177 0.292,0.198 10 false G19 1.844,0.99 2.146,1.188 0.302,0.198 10 false 1*1 2.771,0.99 3.042,1.188 0.271,0.198 10 false 1*3 2.719,1.208 3.094,1.406 0.375,0.198 10 false G154 5.323,1.073 5.458,1.271 0.135,0.198 10 false 7 5.542,1.198 5.667,1.354 0.125,0.156 10 false S 2.26,1.219 2.625,1.417 0.365,0.198 10 false G146 2.271,0.99 2.604,1.188 0.333,0.198 10 false 29*2 0.115,2.948 1.146,3.146 1.031,0.198 10 false *2: for 2TR-FBE 0.094,0.104 1.688,0.479 1.594,0.375 12 false for Gasoline Engine:

E252854
1,1.917 1.365,2.115 0.365,0.198 10 false ECM 5.427,2.156 6.604,2.656 1.177,0.5 10 false Combination Meter Assembly 0.104,2.542 1.844,2.781 1.74,0.24 10 false *1: for 1KD-FTV, 2KD-FTV 0.115,3.344 1.844,3.542 1.729,0.198 10 false *3: for 1KD-FTV (for i-ART) 1.323,1.229 1.76,1.427 0.438,0.198 10 false TACH 1.833,1.219 2.125,1.417 0.292,0.198 10 false G39 5.448,1.99 5.74,2.188 0.292,0.198 10 false G19 1.865,0.99 2.167,1.188 0.302,0.198 10 false 4*1 2.729,0.99 3.042,1.188 0.313,0.198 10 false 18*3 2.708,1.219 3.083,1.417 0.375,0.198 10 false G157 5.323,1.073 5.458,1.271 0.135,0.198 10 false 7 5.531,1.188 5.656,1.344 0.125,0.156 10 false S 2.26,1.229 2.625,1.427 0.365,0.198 10 false G149 2.281,0.99 2.615,1.188 0.333,0.198 10 false 18*2 0.115,2.948 2.396,3.219 2.281,0.271 10 false *2: for 1KD-FTV, 2KD-FTV (for DPF) 0.104,0.094 1.51,0.438 1.406,0.344 12 false for Diesel Engine:

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY
a.
E236122
1.438,0.313 1.969,0.594 0.531,0.281 1.24,1.208 0.74,0.615 true 2.813,3.427 3.156,3.583 0.344,0.156 10 false GND 0.052,0.021 0.219,0.188 0.167,0.167 10 false *a 0.615,0.49 0.74,0.646 0.125,0.156 10 false S 1.573,0.375 1.854,0.542 0.281,0.167 10 false G19
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the G19 combination meter assembly connector.


b.

Using an oscilloscope, check the signal waveform of the meter.

Item Content
Tester Connection G19-7 (S) - Body ground
Tool Setting 5 V/DIV., 10 msec./DIV.
Condition Engine idling

HINT:

As the engine speed increases, the wavelength shortens.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK ENGINE TYPE
2.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
for Gasoline Engine A
for Diesel Engine B




A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G88*1, G146*2 or G154*3 ECM connector.

*1: for 2TR-FE

*2: for 2TR-FBE

*3: for 1GR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G19-7 (S) - G88-1 (TACH) Always Below 1 Ω
G19-7 (S) or G88-1 (TACH) - Body ground Always 10 kΩ or higher


for 2TR-FBE
Tester Connection Condition Specified Condition
G19-7 (S) - G146-29 (TACH) Always Below 1 Ω
G19-7 (S) or G146-29 (TACH) - Body ground Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
G19-7 (S) - G154-1 (TACH) Always Below 1 Ω
G19-7 (S) or G154-1 (TACH) - Body ground Always 10 kΩ or higher

Result:
Result Proceed to
NG A
OK B



HINT:

Refer to SFI system.




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

GO TO SFI SYSTEM

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G39*1, G149*2 or G157*3 ECM connector.

*1: for 1KD-FTV, 2KD-FTV

*2: for 1KD-FTV, 2KD-FTV (for DPF)

*3: for 1KD-FTV (for i-ART)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G19-7 (S) - G39-4 (TACH) Always Below 1 Ω
G19-7 (S) or G39-4 (TACH) - Body ground Always 10 kΩ or higher


for 1KD-FTV, 2KD-FTV (for DPF)
Tester Connection Condition Specified Condition
G19-7 (S) - G149-18 (TACH) Always Below 1 Ω
G19-7 (S) or G149-18 (TACH) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for i-ART)
Tester Connection Condition Specified Condition
G19-7 (S) - G157-18 (TACH) Always Below 1 Ω
G19-7 (S) or G157-18 (TACH) - Body ground Always 10 kΩ or higher

Result:
Result Proceed to
NG A
OK B



HINT:



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

GO TO ECD SYSTEM