Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Operating Light Control Rheostat does not Change Light Brightness  


DESCRIPTION

When the light control rheostat knob is turned right, the combination meter and vehicle interior illumination will become brighter. When the light control rheostat knob is turned left, the combination meter and vehicle illumination will dim.

WIRING DIAGRAM

E224851
1.552,1.99 1.885,2.167 0.333,0.177 10 false G31 1.563,2.146 3.219,2.5 1.656,0.354 10 false Light Control Rheostat 4.313,1.99 4.719,2.188 0.406,0.198 10 false G19 4.323,2.156 6.292,2.5 1.969,0.344 10 false Combination Meter Assembly 4.479,0.917 4.615,1.156 0.135,0.24 10 false 9 2.875,0.927 3.083,1.125 0.208,0.198 10 false 1 1.583,0.344 1.688,0.49 0.104,0.146 10 false 2 4.646,1.031 4.979,1.281 0.333,0.25 10 false TR 2.708,0.927 2.823,1.073 0.115,0.146 10 false T 1.771,0.344 1.885,0.49 0.115,0.146 10 false E

PROCEDURE

1.INSPECT LIGHT CONTROL RHEOSTAT
a.
E224607
0.448,2.469 0.656,2.615 0.208,0.146 10 false *f 1.625,0.104 1.854,0.25 0.229,0.146 10 false *a 1.875,0.438 2.104,0.583 0.229,0.146 10 false *e 2.365,0.76 2.594,0.906 0.229,0.146 10 false *e 2.875,0.833 3.104,0.979 0.229,0.146 10 false *c 2.333,0.292 2.563,0.438 0.229,0.146 10 false *b 2.615,1.271 2.844,1.417 0.229,0.146 10 false *e 3.063,1.531 3.292,1.677 0.229,0.146 10 false *d
*a Position A
*b Position B
*c Position C
*d Position D
*e 30°
*f Component without harness connected
(Light Control Rheostat)


Remove the light control rheostat.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>LIGHT CONTROL RHEOSTAT>REMOVAL


b.

Measure the resistance according to the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Position A 666.9 to 737.1 Ω
1 - 2 Position B 220.4 to 243.6 Ω
1 - 2 Position C 77.9 to 86.1 Ω
1 - 2 Position D Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - LIGHT CONTROL RHEOSTAT)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - LIGHT CONTROL RHEOSTAT)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the G31 light control rheostat connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-9 (TR) - G31-1 (T) Always Below 1 Ω
G19-9 (TR) - Body ground Always 10 kΩ or higher
G31-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR