Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Accessory Meter does not Illuminate  


DESCRIPTION

This circuit provides power to the accessory meter assembly.

WIRING DIAGRAM

E224858
0.531,0.521 1.885,0.813 1.354,0.292 10 false from Ignition Switch 0.552,1.292 1.875,1.573 1.323,0.281 10 false from Ignition Switch 1.021,2.031 1.844,2.375 0.823,0.344 10 false from Battery 3.49,2.208 3.948,2.365 0.458,0.156 10 false DOME 2.656,2.188 3.01,2.344 0.354,0.156 10 false DCC 3.073,1.458 3.438,1.615 0.365,0.156 10 false ACC 4.708,1.313 5.073,1.469 0.365,0.156 10 false ACC 2.698,0.688 3.927,0.844 1.229,0.156 10 false ECU-IG&GAUGE 4.708,2.021 4.938,2.177 0.229,0.156 10 false +B 4.708,0.542 4.958,0.698 0.25,0.156 10 false IG 4.708,2.906 5.177,3.063 0.469,0.156 10 false SGND 4.708,3.656 5.135,3.813 0.427,0.156 10 false GND1 4.427,1.896 4.635,2.052 0.208,0.156 10 false 14 4.427,0.406 4.604,0.563 0.177,0.156 10 false 12 4.427,1.156 4.604,1.313 0.177,0.156 10 false 13 4.427,2.781 4.646,2.938 0.219,0.156 10 false 10 4.5,3.531 4.646,3.688 0.146,0.156 10 false 1 4.479,4.375 6.24,4.656 1.76,0.281 10 false Accessory Meter Assembly 4.469,4.219 4.771,4.375 0.302,0.156 10 false G32

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E224859
1.396,0.635 1.979,0.979 0.583,0.344 1.042,1.729 0.594,1.521 false 1.49,2.188 1.208,2.719 false 1.885,2.177 1.885,2.75 false 2.094,2.188 2.396,2.74 false 2.313,2.021 2.719,1.708 false 1.542,0.719 1.865,0.865 0.323,0.146 10 false G32 0.938,2.76 1.354,2.927 0.417,0.167 10 false SGND 0.156,1.438 0.573,1.604 0.417,0.167 10 false GND1 2.292,2.781 2.792,3.021 0.5,0.24 10 false ACC 2.771,1.604 2.969,1.771 0.198,0.167 10 false +B 1.833,2.792 2.01,2.958 0.177,0.167 10 false IG 0.219,0.188 0.417,0.354 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to Accessory Meter Assembly)


Disconnect the G32 accessory meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G32-12 (IG) - Body ground Ignition switch ON 11 to 14 V
G32-13 (ACC) - Body ground Ignition switch ACC 11 to 14 V
G32-14 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
G32-1 (GND1) - Body ground Always Below 1 Ω
G32-10 (SGND) - Body ground Always Below 1 Ω
G32-12 (IG) - Body ground Always 10 kΩ or higher
G32-13 (ACC) - Body ground Always 10 kΩ or higher
G32-14 (+B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE ACCESSORY METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR