Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2012.10–2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052656 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.

WIRING DIAGRAM

C240167
5.792,2.813 6.01,3 0.219,0.188 10 false 22 5.802,1.823 6.052,2.021 0.25,0.198 10 false 23 5.802,0.813 6,0.99 0.198,0.177 10 false 21 5.51,2.823 5.688,3 0.177,0.177 10 false 5 4.625,2.823 4.802,3 0.177,0.177 10 false 9 5.51,1.823 5.688,2 0.177,0.177 10 false 4 4.625,1.823 4.802,2 0.177,0.177 10 false 8 5.5,0.823 5.677,1 0.177,0.177 10 false 6 4.656,3.604 4.948,3.76 0.292,0.156 10 false G12 6.021,3.604 6.313,3.76 0.292,0.156 10 false G1 2.708,2.094 3.156,2.271 0.448,0.177 10 false MODE 6.063,2.906 6.49,3.083 0.427,0.177 10 false SW2 6.063,1.917 6.49,2.094 0.427,0.177 10 false SWG 6.063,0.906 6.49,1.083 0.427,0.177 10 false SW1 4.969,2.813 5.396,2.99 0.427,0.177 10 false AU2 4.969,1.813 5.396,1.99 0.427,0.177 10 false EAU 4.979,0.813 5.406,0.99 0.427,0.177 10 false AU1 2.75,1.083 3.219,1.302 0.469,0.219 10 false Seek+ 2.135,1.083 2.615,1.323 0.479,0.24 10 false Seek- 1.615,1.083 2.042,1.313 0.427,0.229 10 false Vol+ 1.01,1.083 1.365,1.281 0.354,0.198 10 false Vol- 4.563,0.813 4.74,0.99 0.177,0.177 10 false 10 6.021,3.771 6.979,4.302 0.958,0.531 10 false Radio Receiver Assembly 4.656,3.771 5.563,4.354 0.906,0.583 10 false Spiral Cable Sub-assembly 1.333,3.771 3.344,4.063 2.01,0.292 10 false Steering Pad Switch Assembly 1.344,3.594 1.635,3.75 0.292,0.156 10 false z3

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL

C282179
3.417,0.198 3.729,0.396 0.313,0.198 3.656,0.844 3.979,0.333 3.979,0.333 4.125,0.333 true 3.729,0.833 3.979,0.625 3.979,0.625 4.125,0.625 true 3.542,0.833 3.135,0.479 3.135,0.479 2.979,0.479 true 2.021,1.448 1.854,0.76 1.854,0.76 1.74,0.76 true 1.719,1.479 1.479,0.979 1.479,0.979 1.385,0.979 true 1.677,1.698 1.302,1.271 1.302,1.271 1.188,1.271 true 2.646,2.302 2.521,2.302 2.521,2.302 2.083,1.792 true 1.406,2.552 1.5,2.552 1.5,2.552 1.656,2.115 true 3.51,0.208 3.729,0.396 0.219,0.188 10 false z3 4.198,0.25 4.583,0.448 0.385,0.198 10 false AU2 4.198,0.542 4.583,0.74 0.385,0.198 10 false AU1 2.656,0.406 3.042,0.604 0.385,0.198 10 false EAU 1.583,0.688 1.802,0.885 0.219,0.198 10 false *1 1.229,0.896 1.448,1.094 0.219,0.198 10 false *2 1.021,1.198 1.24,1.396 0.219,0.198 10 false *3 1.25,2.479 1.469,2.677 0.219,0.198 10 false *5 2.677,2.219 2.896,2.417 0.219,0.198 10 false *4 5.281,0.74 5.5,0.938 0.219,0.198 10 false *A
*A w/ Multi-information Display - -
*1 Volume+ Switch *2 Volume- Switch
*3 Seek- Switch *4 Seek+ Switch
*5 MODE Switch - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z3-10 (AU1) - z3-8 (EAU) No switch is pushed 95 to 105 kΩ
Seek+ switch is pushed Below 2.5 Ω
Seek- switch is pushed 312.6 to 345.5 Ω
Volume+ switch is pushed 950 to 1050 Ω
Volume- switch is pushed 2954.5 to 3265.5 Ω
z3-9 (AU2) - z3-8 (EAU) No switch is pushed 95 to 105 kΩ
MODE switch is pushed Below 2.5 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

C282256
1.563,1.01 1.708,0.719 true 1.958,0.99 1.823,0.729 true 2.344,1 1.917,0.719 true 5.781,2.406 5.302,2.042 true 5.427,2.396 5.208,2.052 true 4.927,2.406 5.125,2.042 true 1.375,0.156 1.688,0.354 0.313,0.198 10 false *a 4.604,1.5 4.917,1.698 0.313,0.198 10 false *b 1.438,1.021 1.896,1.219 0.458,0.198 10 false AU1 1.875,1.021 2.333,1.219 0.458,0.198 10 false AU2 2.302,1.021 2.76,1.219 0.458,0.198 10 false EAU 5.75,2.417 6.208,2.615 0.458,0.198 10 false AU1 5.333,2.417 5.792,2.615 0.458,0.198 10 false AU2 4.792,2.417 5.25,2.615 0.458,0.198 10 false EAU
*a Steering Pad Switch Side *b Vehicle Side


Standard Resistance:
Tester Connection Condition Specified Condition
8 (EAU) - 4 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
10 (AU1) - 6 (AU1) Spiral cable is turned 2.5 rotations counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise
9 (AU2) - 5 (AU2) Spiral cable is turned 2.5 rotations counterclockwise
Spiral cable is centered
Spiral cable is turned 2.5 rotations clockwise


CAUTION:

The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)
a.

Disconnect the G1 radio receiver assembly connector.


b.

Disconnect the G12 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-21 (SW1) - G12-6 (AU1) Always Below 1 Ω
G1-22 (SW2) - G12-5 (AU2)
G1-23 (SWG) - G12-4 (EAU)
G1-21 (SW1) - Body ground Always 10 kΩ or higher
G1-22 (SW2) - Body ground
G1-23 (SWG) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR