Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.04–2012.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio and display receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

C240216
5.333,4.708 5.635,4.875 0.302,0.167 10 false Z6 5.333,4.198 5.635,4.365 0.302,0.167 10 false Z6 1.677,2.948 1.885,3.104 0.208,0.156 10 false 9 1.677,2.438 1.885,2.594 0.208,0.156 10 false 7 1.677,1.927 1.885,2.083 0.208,0.156 10 false 5 1.677,1.427 1.885,1.583 0.208,0.156 10 false 6 1.677,3.458 1.885,3.615 0.208,0.156 10 false 8 1.677,4.594 1.885,4.75 0.208,0.156 10 false 3 1.677,4.083 1.885,4.24 0.208,0.156 10 false 2 5.323,2.865 5.531,3.021 0.208,0.156 10 false 11 1.135,4.188 1.563,4.344 0.427,0.156 10 false UDO- 1.135,4.688 1.563,4.844 0.427,0.156 10 false UDO+ 5.698,4.188 6.125,4.344 0.427,0.156 10 false US1- 5.698,4.677 6.125,4.833 0.427,0.156 10 false US1+ 1.135,3.052 1.563,3.208 0.427,0.156 10 false AGND 1.146,2.542 1.573,2.698 0.427,0.156 10 false ASGN 1.229,2.031 1.563,2.188 0.333,0.156 10 false ARO 1.25,1.521 1.563,1.677 0.313,0.156 10 false ALO 1.135,3.552 1.563,3.708 0.427,0.156 10 false AUXO 5.698,3.052 6.125,3.208 0.427,0.156 10 false AGND 5.698,3.542 6.125,3.698 0.427,0.156 10 false ADPG 5.333,2.365 5.542,2.521 0.208,0.156 10 false 27 5.698,2.542 6.125,2.698 0.427,0.156 10 false VA- 5.333,1.854 5.542,2.01 0.208,0.156 10 false 26 5.677,2.021 6.104,2.177 0.427,0.156 10 false VAR+ 5.333,1.333 5.563,1.49 0.229,0.156 10 false 28 5.677,1.51 6.104,1.667 0.427,0.156 10 false VAL+ 5.24,3.063 5.625,3.229 0.385,0.167 10 false G127 5.24,2.552 5.625,2.719 0.385,0.167 10 false G127 5.24,2.042 5.625,2.208 0.385,0.167 10 false G127 5.24,3.573 5.625,3.74 0.385,0.167 10 false G127 5.24,1.531 5.625,1.698 0.385,0.167 10 false G127 5.333,3.375 5.542,3.531 0.208,0.156 10 false 25 5.365,4.51 5.573,4.667 0.208,0.156 10 false 3 5.365,4 5.573,4.156 0.208,0.156 10 false 2 0.625,5.708 1.771,6.156 1.146,0.448 10 false No. 1 Stereo Jack Adapter Assembly 0.625,5.531 0.948,5.719 0.323,0.188 10 false z1 5.49,5.688 6.677,6.208 1.188,0.521 10 false Radio and Display Receiver Assembly 4.021,3.229 4.615,3.406 0.594,0.177 10 false Shielded 2.573,3.229 3.167,3.406 0.594,0.177 10 false Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - STEREO JACK ADAPTER)
a.

Disconnect the G127 and z6 radio and display receiver assembly connectors.


b.

Disconnect the z1 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-28 (VAL+) - z1-6 (ALO) Always Below 1 Ω
G127-26 (VAR+) - z1-5 (ARO)
G127-27 (VA-) - z1-7 (ASGN)
G127-11 (AGND) - z1-9 (AGND)
G127-25 (ADPG) - z1-8 (AUXO)
z6-2 (US1-) - z1-2 (UDO-)
z6-3 (US1+) - z1-3 (UDO+)
G127-28 (VAL+) - Body ground Always 10 kΩ or higher
G127-26 (VAR+) - Body ground
G127-27 (VA-) - Body ground
G127-11 (AGND) - Body ground
G127-25 (ADPG) - Body ground
z6-2 (US1-) - Body ground
z6-3 (US1+) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR