Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0069  MAP Sensor Too High or Too Low  


DESCRIPTION

To detect atmospheric pressure, the atmospheric pressure sensor built into the ECM is used in the common rail system. Following the changes in the atmospheric pressure, the ECM corrects the fuel injection volume, timing and duration, and adjusts the common rail internal fuel pressure to optimize combustion.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0069 MAP Sensor Too High or Too Low After the ignition switch is turned to ON, the difference between the atmospheric pressure sensor output and manifold absolute pressure sensor output is more than 8 kPa for 0.5 seconds (2 trip detection logic). ECM Comes on DTC stored

Related Data List
DTC No. Data List
P0069
·

Atmosphere Pressure

·

MAP



HINT:
·

Turn the ignition switch to ON and check the Atmosphere Pressure and MAP items in the Data List. If the atmospheric pressure displayed on the tester differs greatly from the actual atmospheric pressure (standard: 101 kPa), the sensor (atmospheric pressure sensor or manifold absolute pressure sensor) is malfunctioning.

·

If DTC P0069 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

P0069
DTC Detection Drive Pattern 1 second elapses after ignition switch turnedfrom off to ON (starter remains off)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:
·

Although the DTC titles say Manifold Absolute Pressure Sensor Too High or Too Low, these DTCs relate to the atmospheric pressure sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0069)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0069 is output A
DTC P0069 and other DTCs are output B


HINT:

If codes other than P0069 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR

B

2.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR
HINT:

Before inspecting the manifold absolute pressure sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine > Data List
Tester Display
MAP
50003 61 314

e.

Read the value.

OK:

Same value as the actual atmospheric pressure.



Result:
Proceed to
OK
NG



OK

3.REPLACE CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

3.REPLACE CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTC.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Turn the ignition switch to ON for 1 second.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT