Refer to DTC P0031 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0031).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2195 | Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) | While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor voltage is 2.65 V or more for 3.5 seconds
(2 trip detection logic) |
·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| DTC Detection Drive Pattern | After the engine is fully warmed up, the accelerator pedal is released for 10 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph). |
When the air fuel sensor output indicates a lean value due to a malfunction in the sensor, the system cannot determine whether the air fuel ratio is rich and particulate matter may build up excessively in the DPF catalyst. The ECM monitors the air fuel ratio sensor voltage value when a fuel-cut is performed and detects whether this voltage value is abnormal. When the air fuel ratio sensor voltage value is 2.65 V or higher for 3.5 seconds or more, the ECM determines that the air fuel ratio sensor is malfunctioning and stores DTC P2195.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>AIR FUEL RATIO SENSOR(w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and warm it up.
After the engine is fully warmed up, the accelerator pedal is released for 10 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph).
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the pending DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P2195.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
|---|---|---|
| All Readiness | NORMAL | A |
| ABNORMAL | B | |
| Pending DTC | DTC P2195 is output |
If STATUS is INCOMPLETE or N/A, the accelerator pedal is released for 10 seconds or more immediately after the vehicle is accelerated to a speed of between 60 and 80 km/h (37 and 50 mph) again.
A
B