Home › Drivetrain › A343F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2012.10
RM1840EF _52 Drivetrain _009611 A343F AUTOMATIC TRANSMISSION / TRANSAXLE _0052478 AUTOMATIC TRANSMISSION SYSTEM C

A343F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0818  Driveline Disconnect Switch Input Circuit  


DESCRIPTION

The ECM detects the signal from the transfer neutral position switch.

This DTC indicates that the transfer neutral position switch remains on.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0818 Driveline Disconnect Switch Input Circuit Transfer neutral position switch remains on while vehicle is being driven under following conditions for 30 sec. (2-trip detection logic):
·

Vehicle speed is 25 km/h (16 mph) or more

·

Transfer shift lever is in H


·

Short in transfer neutral position switch circuit

·

Transfer neutral position switch

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM detects whether or not the transfer shift lever is in neutral by monitoring the signal from the transfer neutral position switch.

If the transfer neutral position switch indicates that the transfer shift lever is in neutral under all of the following conditions, the ECM will conclude that there is a malfunction of the transfer neutral position switch.

·

The transfer shift lever is in the H position.

·

The vehicle is traveling at 25 km/h (16 mph) or more.

·

The transfer neutral position switch has been on for more than 30 seconds.


Then the ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C154998
6.094,2.938 6.615,3.146 0.521,0.208 10 ECM 5.938,1.313 6.458,1.521 0.521,0.208 10 TFN 5.625,1.406 5.927,1.615 0.302,0.208 10 23 3.646,1.396 3.802,1.604 0.156,0.208 10 1 2.885,1.406 3.073,1.615 0.188,0.208 10 2 6.094,2.76 6.615,2.969 0.521,0.208 10 G146 2.323,1.583 2.844,1.792 0.521,0.208 10 C30 2.323,1.781 4.323,2.156 2,0.375 10 No. 2 Transfer Indicator Switch (N Position Switch)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - BODY GROUND)
a.
C237850
0.058,0.017 0.313,0.238 0.256,0.221 10 *a 0.325,0.971 0.763,1.234 0.439,0.263 0.39,1.013 0.734,1.181 0.344,0.167 10 C30
*a Front view of wire harness connector
(to No. 2 Transfer Indicator Switch)


Disconnect the C30 No. 2 transfer indicator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT NO.2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO.2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)
a.
C237864
0.057,0.0050 0.237,0.207 0.179,0.202 10 *a 0.232,2.754 0.411,2.956 0.179,0.202 10 *c 0.968,2.754 1.147,2.956 0.179,0.202 10 *b
*a Component without harness connected
(No. 2 Transfer Indicator Switch)
*b Pushed
*c Not pushed


Remove the No. 2 transfer indicator switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
1 - 2 Pushed Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - ECM)

NG

REPLACE NO.2 TRANSFER INDICATOR SWITCH (TRANSFER NEUTRAL POSITION SWITCH)

3.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSFER INDICATOR SWITCH - ECM)
a.

Disconnect the C30 No. 2 transfer indicator switch connector.


b.

Disconnect the G146 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C30-1 - G146-23 (TFN) Always Below 1 Ω
C30-1 or G146-23 (TFN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR