Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0226/21  SFR Solenoid Circuit  C0236/22  SFL Solenoid Circuit  C0246/23  SRR Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C0226/21 SFR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid (SFRR or SFRH) circuit

·

Brake actuator assembly


C0236/22 SFL Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid (SFLR or SFLH) circuit

·

Brake actuator assembly


C0246/23 SRR Solenoid Circuit Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Solenoid (SRRR or SRRH) circuit

·

Brake actuator assembly



WIRING DIAGRAM

C237084
1.219,1.323 2,1.521 0.781,0.198 10 false ABS NO. 2 0.396,2 1.313,2.219 0.917,0.219 10 false from Battery 2.635,1.042 3.01,1.25 0.375,0.208 10 false +BS 2.635,3 3.125,3.208 0.49,0.208 10 false GND1 2.635,3.854 3.125,4.063 0.49,0.208 10 false GND2 2.313,0.927 2.5,1.135 0.188,0.208 10 false 1 2.313,2.865 2.521,3.042 0.208,0.177 10 false 2 2.313,3.719 2.521,3.885 0.208,0.167 10 false 24 4.094,1.063 5.448,1.438 1.354,0.375 10 false ABS Solenoid Relay 4.021,5.229 5.219,5.542 1.198,0.313 10 false Skid Control ECU 3.823,6.104 5.51,6.479 1.688,0.375 10 false Brake Actuator Assembly 3.823,5.896 4.313,6.073 0.49,0.177 10 false A13 5.969,1.917 6.427,2.073 0.458,0.156 10 false SFRR 5.969,2.427 6.427,2.583 0.458,0.156 10 false SFRH 5.969,2.927 6.427,3.083 0.458,0.156 10 false SFLR 5.969,3.427 6.427,3.583 0.458,0.156 10 false SFLH 5.969,3.927 6.427,4.083 0.458,0.156 10 false SRRR 5.969,4.438 6.427,4.594 0.458,0.156 10 false SRRH

PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly). Therefore, the solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B