Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.01–2012.04
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241/41  Low Battery Positive Voltage or Abnormally High Battery Positive Voltage  


DESCRIPTION

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage Either condition is met:
1.

Both conditions continue for at least 10 seconds.

·

Vehicle speed is more than 3 km/h (2 mph).

·

The IG1 terminal voltage is below 9.5 V.


2.

All conditions continue for at least 0.2 seconds

·

Solenoid relay remains on.

·

Relay contact is open.

·

The IG1 terminal voltage is below 9.5 V.



·

ECU-IG&GAUGE fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C237089
2.26,1.229 3.49,1.396 1.229,0.167 10 false ECU-IG&GAUGE 4.708,1.073 5.01,1.25 0.302,0.177 10 false IG1 4.354,0.969 4.583,1.125 0.229,0.156 10 false 25 0.396,1.063 1.385,1.24 0.99,0.177 10 false from IG Circuit 4.698,1.76 5.135,1.969 0.438,0.208 10 false GND1 4.698,2.427 5.135,2.635 0.438,0.208 10 false GND2 4.354,2.313 4.583,2.469 0.229,0.156 10 false 24 4.354,1.656 4.583,1.813 0.229,0.156 10 false 2 4.125,3.042 4.51,3.198 0.385,0.156 10 false A13 4.125,3.229 7.01,3.438 2.885,0.208 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2KD-FTV) C
NG (for 2TR-FE) D
NG (for 2TR-FBE) E




A

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

B

C

D

E

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C117862
1.531,0.646 1.885,0.885 0.354,0.24 1.438,2.823 1.365,2.823 1.365,2.823 1.313,2.229 false 0.104,0.063 0.417,0.219 0.313,0.156 10 *a 1.594,0.688 2,0.906 0.406,0.219 10 A13 1.5,2.729 1.906,2.948 0.406,0.219 10 IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-25 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
C117862
1.521,0.667 1.875,0.906 0.354,0.24 1.042,1.854 0.802,1.031 0.802,1.031 0.667,1.031 false 1.083,2.146 1.521,2.771 1.521,2.771 1.688,2.771 false 0.073,0.063 0.385,0.219 0.313,0.156 10 *a 1.573,0.708 1.99,0.917 0.417,0.208 10 A13 0.26,0.958 0.76,1.177 0.5,0.219 10 GND1 1.729,2.688 2.229,2.906 0.5,0.219 10 GND2
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (GND1) - Body ground Always Below 1 Ω
A13-24 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B