Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1282/82  Center Differential Lock Position Switch Malfunction (Test Mode DTC)  


DESCRIPTION

DTC C1282/82 is output only in Test Mode.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1282/82 Center Differential Lock Position Switch Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Transfer system

·

Harness or connector

·

Skid control ECU (Brake actuator assembly)



*C1282/82: for 4WD

HINT:

The codes in this table are output only in Test Mode.


WIRING DIAGRAM

C283183
1.302,0.688 1.646,0.885 0.344,0.198 10 false ADD 1.771,0.677 1.927,0.875 0.156,0.198 10 false 8 2.479,3.375 2.635,3.573 0.156,0.198 10 false *1 5.125,0.677 5.302,0.896 0.177,0.219 10 false 17 5.427,0.677 5.688,0.896 0.26,0.219 10 false EXI 5.302,1.417 5.781,1.625 0.479,0.208 10 false A13 5.292,1.583 6.844,2.042 1.552,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 2.031,1.583 2.375,1.781 0.344,0.198 10 false ADD 2.021,1.969 2.365,2.167 0.344,0.198 10 false GND 2.49,1.333 2.646,1.531 0.156,0.198 10 false 3 2.729,1.448 3.063,1.667 0.333,0.219 10 false C31 2.74,1.625 4.156,2.24 1.417,0.615 10 false 4WD Detection Switch (Differential Vacuum Actuator Assembly)*1 2.469,2.208 2.625,2.406 0.156,0.198 10 false 4 1.396,3.385 1.74,3.583 0.344,0.198 10 false DL 1.792,3.396 2.135,3.594 0.344,0.198 10 false 6 4.573,3.396 4.729,3.594 0.156,0.198 10 false 2 2.875,0.677 3.031,0.875 0.156,0.198 10 false *1 4.26,2.313 4.417,2.51 0.156,0.198 10 false *2 5.802,3.396 5.958,3.594 0.156,0.198 10 false 1 4.625,4.156 6.375,4.552 1.75,0.396 10 false 4WD Position Switch (No. 3 Transfer Indicator Switch) 4.615,3.958 4.906,4.177 0.292,0.219 10 false C28 0.167,4.042 0.458,4.26 0.292,0.219 10 false C37 0.177,4.25 2.125,4.542 1.948,0.292 10 false 4 Wheel Drive Control ECU*1 0.125,4.698 3.104,4.938 2.979,0.24 10 false *1: w/ Differential Vacuum Actuator Assembly 0.125,4.948 3.104,5.188 2.979,0.24 10 false *2: w/o Differential Vacuum Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (EXI TERMINAL)
a.
C117862
1.521,0.625 1.896,0.875 0.375,0.25 2.052,2.76 1.958,2.76 1.958,2.76 1.958,2.042 false 0.094,0.052 0.406,0.208 0.313,0.156 10 *a 1.594,0.667 1.979,0.896 0.385,0.229 10 A13 2.104,2.677 2.49,2.906 0.385,0.229 10 EXI
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Set the vehicle to the 4WD state using the transfer shift lever.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-17 (EXI) - Body ground
·

Ignition switch ON

·

Transfer shift position H4


Below 1.5 V



d.

Connect the skid control ECU (brake actuator assembly) connector.


e.

Set the vehicle to the 2WD state using the transfer shift lever.


f.

Disconnect the skid control ECU (brake actuator assembly) connector.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-17 (EXI) - Body ground
·

Ignition switch ON

·

Transfer shift position H2


11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TEST MODE DTC

NG

3.CHECK HARNESS AND CONNECTOR (EXI CIRCUIT)
2.CHECK TEST MODE DTC
a.

Switch the vehicle to Test Mode, perform the H2 to L4 shift operation check, and then check that DTC C1282/82 is not stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

Result:
Result Proceed to
DTC is stored A
DTC is not stored B




A

B

3.CHECK HARNESS AND CONNECTOR (EXI CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

w/ Differential Vacuum Actuator Assembly: Disconnect the 4WD detection switch (differential vacuum actuator assembly) connector. w/o Differential Vacuum Actuator Assembly: Disconnect the 4WD position switch (No. 3 transfer indicator switch) connector.


d.

w/ Differential Vacuum Actuator Assembly: Disconnect the 4 wheel drive control ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Differential Vacuum Actuator Assembly:
Tester Connection Condition Specified Condition
A13-17 (EXI) - C31-3 (ADD) Always Below 1 Ω
A13-17 (EXI) - C37-8 (ADD) Always Below 1 Ω
A13-17 (EXI) - Body ground Always 10 kΩ or higher
C31-4 (GND) - Body ground Always Below 1 Ω

w/o Differential Vacuum Actuator Assembly:
Tester Connection Condition Specified Condition
A13-17 (EXI) - C28-2 Always Below 1 Ω
A13-17 (EXI) - Body ground Always 10 kΩ or higher
C28-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR